Robotis DYNAMIXEL XM430-W210 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 34

background image

2/22/2018

ROBOTIS e-Manual

http://emanual.robotis.com/docs/en/dxl/x/xm430-w210/

28/34

This value indicates current Current. For more details, please
refer to the

Goal Current(102)

2. 4. 39. Present Velocity(128)

This value indicates current Velocity. For more details, please
refer to the Goal Velocity(104)](#goal-velocity).

2. 4. 40. Present Position(132)

This value indicates present Position. For more details, please
refer to the

Goal Position(116)

Note

Present Position(132) represents 4 byte continuous

range(-2,147,483,648 ~ 2,147,483,647) when Torque is turned off
regardless of Operating Mode(11). However, Present
Position(132) will be reset in those cases:

1. Present Position(132) is reset with the value within 1 rev (0 ~

4,095) when Operating Mode(11) is changed to Position
Control Mode.

2. Present Position(132) is reset with the value within 1 rev (0 ~

4,095) when Torque is turned on in Position Control Mode.

Reset Present Position(132) value can be affected by Homing
Offset(20).

2. 4. 41. Velocity Trajectory(136)

This is a target velocity trajectory created by Profile. Operating
method can be changed based on control mode. For more
details, please refer to the Profile Velocity(112).

1. Velocity Control Mode : When Profile reaches to the

endpoint, Velocity Trajectory(136) becomes equal to Goal
Velocity(104).

2. Position Control Mode, Extended Position Control

Mode, Current-based Position Control Mode : Velocity
Trajectory is used to create Position Trajectory(140). When
Profile reaches to an endpoint, Velocity Trajectory(136) is
cleared to ‘0’.

2. 4. 42. Position Trajectory(140)

This is a target position trajectory created by Profile. This value
is only used in Position Control Mode, Extended Position
Control Mode and Current-based Position Control Mode. For
more details, please refer to the

Profile Velocity(112)

2. 4. 43. Present Input Voltage(144)

Back to Top ▲

«
...
26
27
28
29
30
...
»

Содержание DYNAMIXEL XM430-W210



































Отзывы:

Нет отзывов

Похожие инструкции для DYNAMIXEL XM430-W210

Бренд: Cadman Страницы: 66

Бренд: Paia Страницы: 11

Бренд: CAB Страницы: 39

Бренд: CAB Страницы: 27

Бренд: idi Страницы: 20

Бренд: G&G Страницы: 2

Бренд: H&S Страницы: 46

Бренд: OceanSat Страницы: 85

Бренд: Halyard Страницы: 88

Бренд: HALDER Страницы: 2

Бренд: Hällde Страницы: 40

Бренд: Hällde Страницы: 6

Бренд: Nemalux Страницы: 6

Бренд: OBDLink Страницы: 2

i-limb access hand

Бренд: Össur Страницы: 246

PROPRIO FOOT PSX01

Бренд: Össur Страницы: 374

Бренд: ICS Страницы: 156

Бренд: SCHUNK Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды