ROBOTIQ Gripper Скачать руководство пользователя страница 75 | Manualshive

Страница: 75 / 125

background image

Robotiq 3-Finger Adaptive Robot Gripper

Instruction Manual

Robotiq inc. © 2008 - 2014

75

4.8 MODBUS TCP communication protocol

The Robotiq

can be controlled using the Modbus TCP protocol. This section is intended to provide

3-Finger Gripper

guidelines for setting up a Modbus TCP communication link to adequately send commands to and read inputs from
the Gripper.

For a general introduction to Modbus TCP and to understand its differences from Modbus RTU, the reader is invited
to review the information provided on the following website:

http://www.simplymodbus.ca/TCP.htm

Note

The Adaptive Gripper register values are updated at a 100Hz frequency. It is therefore
recommended to send commands with a minimum interval delay of 10ms. Note that the updated
frequency may drop under some conditions where the response time would be longer.

4.8.1 Connection Setup

The following table describes the connection requirement for controlling the Robotiq

using the

3-Finger Gripper

Modbus TCP protocol.

CONNECTION REQUIREMENT

VALUE

Required protocol

TCP/IP

Port

502

Gripper IP address

Configurable (most Grippers are shipped with the

192.168.1.11 address)

Supported Functions

Read Input Registers (FC04)

Preset Multiple Registers (FC16)

UnitID

0x0002 (2)

Robot Output / Gripper Input First Register

0x0000 (0000)

Robot Input / Gripper Output First Register

0x0000 (0000)

Each register (word - 16 bits) of the Modbus TCP protocol is composed of registers (bytes – 8 bits) from the

2

Robotiq

. The first Gripper output Modbus register (0x0000) is composed from the first Robotiq

3-Finger Gripper

2

3-Finger Adaptive Robot Gripper registers (byte 0 and byte 1).

«
...
73
74
75
76
77
...
»

Содержание Gripper






























































































































Отзывы:

Нет отзывов

Похожие инструкции для Gripper

Бренд: ABB Страницы: 34

Бренд: I&J Fisnar Страницы: 108

Arduino Robotics Kit With Motor Shield

Бренд: oddWires Страницы: 28

Бренд: Ebotics Страницы: 78

Бренд: UFactory Страницы: 184

Бренд: YahBoom Страницы: 57

Бренд: Polaris Страницы: 72

Бренд: Kettler Страницы: 15

Бренд: Kettler Страницы: 23

Бренд: First Страницы: 34

Бренд: COVVI Страницы: 83

Бренд: COVVI Страницы: 90

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды