background image

 

Page 2 of 12 

conditions

.    If  necessary,  should  keep  the  equipment  working  in  the 

suitable  temperature  &  humidity  (within  the  restrained  scope).  We 
recommend operating unit in a dust free environment. 

3.

 

EDFA equipment can be powered by AC or steady DC voltage. In both of 

AC & DC, AC is the main power supply. 
Request of power supply: 

AC input   

94-245VAC, 50-60Hz 

DC input   

36-60VDC, (48V source recommended)   

Power consumption 

Maximum 50W 

4.

 

The DC power supply of the equipment must be the SELV supply type 

as stipulated in the CAN/CSA C22.2 No.950-95 standard. 

5.

 

Unit  should  have  good  grounding  with  grounding  resistance

4Ω

According to common international standards, AC plugs must be tri-wire with

 

the middle wire being the grounding wire. 

Before connecting power circuit, please use appropriate (#20AWG or more) 
electric wire to connect the grounding screw on the bottom to the grounding 
frame. When using DC input power supply, the equipment chassis must be 
grounded following the appropriate procedures for the respective location. 

 

2.3

 

Optical connectivity 

1.

 

Clean all fiber patch cords before connecting to the EDFA unit. 

Cleaning Guidelines: 

Fiber Patch cord connectors 

-  Remove  the  dust  cap  of  the  fiber  connectors  and  wipe  the  fiber 
connector tip with a dry lint-free cloth. Check if there are scratches or 
debris on the connector surface by using a microscope (ie.100x or 200x). 

- If no scratch or debris are found, the connector is ready for connection. 
If scratches or debris are found, repeat the fiber patch cord connector 
cleaning guidelines. 

Fiber Bulkhead connectors 

- Compressed air may be used to clean fiber bulkhead connectors. Use 
compressed air according to the following specifications (at least): 

- Non-residue, inert gas for precision dust removal 

- Ultra-filtered to < 0.2 microns 

- Recommended for optical systems 

- Using compressed air as listed above, remove the bulkhead dust 
cover and hold the can of compressed air about 6 inches away from 
the connector. After spraying a few short bursts into the bulkhead, 

Содержание EDFA-4429 Series















Отзывы: