ROBINHOOD RWE3CH6SS Скачать руководство пользователя страница 7

 

Operating instructions

 

Controls 

        

 

 

Light 

The light can be operated independently from the fan and is controlled in accordance with the graphics printed 
above. 

 

Fan 

The fan is operated by turning the power switch on.  It can be run at three different speeds (Speed 1 / Speed 2 / 
Speed 3) depending on the cooking requirements and is controlled in accordance with the graphics printed above. 

Cleaning and Maintenance

 

General Maintenance 

Switch off the canopy before cleaning or maintenance.  

To prevent surface damage never use abrasive 

or oil based liquid cleaners.  To clean the surfaces of the appliance, use mild detergent and warm water.  In 
areas of high humidity and coastal environments cleaning should be carried out frequently. 
 

Warning: a build up of oil may occur if the compact canopy is not cleaned regularly. 

 

Filter Maintenance 

To maintain efficiency, the filters should be removed regularly (approximately monthly), and washed using hot 
soapy water or the dishwasher.  

Note - some discolouration of the frame may occur if washed in the 

dishwasher.

   

 
Rangehoods fitted with charcoal filters are designed to remove grease and odours from cooking vapours prior to 
the cleansed air re-entering the kitchen (when the rangehood is in recirculation mode).  Charcoal filters should be 
replaced every two to four months depending on use. 
 
Note: Fully saturated charcoal filters can become a barrier to air movement therefore limiting rangehood 
performance.  In the event of fire, grease laden filters could be flammable and therefore regular replacement is 
recommended.  In ducted installations, conventional aluminium filters are recommended. 
 

Replacement of Halogen Lamps 

To replace a lamp, first disconnect the rangehood from the power supply.  Use a small blade screwdriver to prise 
off the lamp cover.  Care must be taken to avoid the lamp lens falling on to the hob top.  The halogen bulb is a 
push fit into the lamp body.  Insert the replacement lamp into the lamp holder and replace the lens and lamp 
cover. 

 

Parts and Accessories list 

 

o

 

Charcoal filter                                       2536 (2 pack - 600 Model) 

2537 (3 pack - 900 Model) 

o

 

Light bulb 12V 20W                              

   

104467

 

o

 

Chimney extensions                              

 

2611 (10 ft/3048mm)

 

2612 (12 ft/3658mm) 

 

For any other problems please call help line on NZ 0800 760 667 or AUS 1800 648 556

 

 

 

 

 

   Lights On/Off

 

   

Power On/Off

 

Speed 1               Speed 2                 Speed 3

 

Содержание RWE3CH6SS












Отзывы: