Robin America EH63 Скачать руководство пользователя страница 15

Страница: 15 / 85

– 12 –

4-14 CARBURETOR

The engine is equipped with a down draft carburetor

that has a float controlled fuel system and a fixed

main jet.

The carburetors are calibrated carefully for the sure

starting, low fuel consumption and sufficient output.

Fuel cut solenoid valve is provided to prevent engine

running on when the key switch is turned to off.

Accelerator-pump is provided for obtaining quick and

good throttle response. (EH72D)

4-15 AIR CLEANER

The air-cleaner is a heavy-duty type with a dual

element system ; primary side is urethane foam

(half-wet) and secondary side is dry type.

ACCELERATOR-PUMP

FUEL CUT
SOLENOID VALVE

URETHANE FOAM

ELEMENT

WING NUT

CLEANER COVER

4-16 FUEL PUMP

The engine is equipped with a diaphragm type fuel

pump which is operated by the crankcase inside

vacuum pressure.

FUEL PUMP

Содержание EH63





















































































Результаты поиска

Содержание EH63

Отзывы:

Похожие инструкции для EH63

Бренды по названию

Популярные бренды

Robin America EH63, Руководство по обслуживанию

Результаты поиска

Содержание EH63

Отзывы:

Похожие инструкции для EH63

Бренды по названию

Популярные бренды