background image

Technical Data

Power Requirements

120 VAC, 60 Hz, 

. . . . . . . . . . . . . 

1 Phase, 15 AMP minimum

Pressure Operating Range

0–3000 psi 

. . . . . . . . . . . . . 

(0 – 210 bar)

Maximum Delivery

0.28 GPM (1.1 liter/min)

. . . . . . . . . . 

Power Cord

No. 16 AWG, 3 wire, 

. . . . . . . . . . . . . . . . . . 

8.5 feet (2.6 m) long

Inlet Strainer

16 mesh

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Fluid Outlet Nipple

1/4 npsm (m)

. . . . . . . . . . . . . . . . . . . . 

Weight – without hose and gun

33 lb (14.8 Kg)

. . . . . . . 

Dimensions

Height: 20 inch (508 mm)

. . . . . . . . . . . . . . . 

Width: 17.5 inch (444.5 mm)

Depth: 17.5 inch (444.5 mm)

Wetted Parts

Stainless Steel, Zinc-Plated Steel, 

. . . . . 

Carbide, Aluminum, Nylon, Delrin

r

, Monel

 

Delrin

r

 is a registered trademark of the DuPont Company

Ordering and 

Technical Assistance

TO PLACE AN ORDER

, contact your Graco distrib-

utor, or call this number to identify the distributor
closest to you: 

1–800–367–4023 Toll Free

FOR TECHNICAL ASSIST

ANCE,

 service repair

information or assistance regarding the application of
Graco equipment: 

1–800–543–0339 Toll Free

The Graco Warranty and Disclaimers

WARRANTY

Graco warrants all equipment manufactured by it and bearing its name to be free from defects in material and workmanship on
the date of sale by an authorized Graco distributor to the original purchaser for use. As purchaser’s sole remedy for breach of this
warranty, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment proven defec-
tive, with the exception of defects in parts on the drive train/gear box on EM and GM sprayers or power train on EH and GH
sprayers, which will be repaired or replaced for twenty-four months from the date of sale for Gas–Hydraulic (GH) and Gas-
Mechanical (GM) sprayers and for thirty-six months from the date of sale for Electric-Mechanical (EM), Electric-Hydraulic (EH),
390st and 490st sprayers

.

 This warranty applies only when the equipment is installed, operated and maintained in accordance

with Graco’s written recommendations.
This warranty does not cover, and Graco shall not be liable for, any malfunction, damage or wear caused by faulty installation,
misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of
non–Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility with Graco
equipment of structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, instal-
lation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor
for verification of the claim. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The
equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any
defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts,
labor and transportation.

DISCLAIMERS AND LIMITATIONS

The terms of this warranty constitute purchaser’s sole and exclusive remedy and are in lieu of any other warranties (express or
implied), 

including warranty of merchantability or warranty of fitness for a particular purpose,

 and of any non–contractual

liabilities, including product liabilities, based on negligence or strict liability. Every form of liability for direct, special or consequen-
tial damages or loss is expressly excluded and denied. In no case shall Graco’s liability exceed the amount of the purchase price.
Any action for breach of warranty must be brought within two (2) years of the date of sale.

EQUIPMENT NOT COVERED BY GRACO WARRANTY

Graco makes no warranty, and disclaims all implied 

warranties of merchantability and fitness for a particular purpose

, with

respect to accessories, equipment, materials, or components sold but not manufactured by Graco. These items sold, but not
manufactured by Graco (such as electric motor, switches, hose, etc.) are subject to the warranty, if any, of their manufacturer.
Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties.

ROBERTS CONSOLIDATED INDUSTRIES, INC.
P.O. Box 1250 / 600 N. Baldwin Park Blvd.
City of Industry, California 91749
(213) 338–7311 or (800) 423–9467

PRINTED IN U.S.A. 308–021 November, 1989; Revised December, 1994

Содержание 61-251

















Отзывы: