9
If you want to return to the factory setting, press and hold the STEP and TIME-button at the same time for 10s.
If you want delete dedicated the times of the program steps and set the programs no. 21-30 to minimum length (1
step), press and hold the PROGRAM- button and then press the ENTER- button. Hold both buttons until the reset
has run (approximately 3 s).
Set up mode is finished by pressing the ENTER- button. Setting all LED diodes in this moment is written in
EEPROM and will be used as an initial state of the controller. Before finishing the adjusting mode, check the
trigger mode (AUTO, MUSIC, TRIG) and the speed mode (SLOW, MEDIUM, FAST) for every fixture.
Calling up a programs
Select the desired program between 1- 30,
CH
,
rn
via the PROGRAM UP/DOWN buttons.The program runs 1.5 s
after showing on the PROGRAM-DISPLAY.
The selection
„CH“
means that the programs 21- 30 will be run through (chain).
The selection
„rn“
means that the programs 21- 30 will be run randomly selected.
Programs from 21 to 30 - freely-programmable chasers.
Programs from 1 to 10 - pre-programed for the projectors with the 6 control channels(ClubScan 150/250 CT).
Programs from 11 to 20 - pre-programed for the moving heads with the 6 control channels(ClubSpot 150/160 CT).
Note:Only programs 21-30 are used for the options "
CH
" and "
rn
"
Adjusting the program-speed
The programs run through the selected program step by step with the programmed speed. You can adjust the
program-speed via the SLOW SPEED- button, MEDIUM SPEED- button or FAST SPEED- button.
Jump from one step to another
Via the MANUAL TRIG- button, you have the possibility to jump from one step to another.
If a program is run and the MANUAL TRIG- button is pressed, the projector jumps to the next step after finishing
the current step. The MANUAL TRIG-LED shines and the program is stopped.
If you wish to start the program once more, press the AUTO TRIG- button or the MUSIC TRIG- button.
Activating the sound-control
If the sound-control is activated, the program moves in the bass-tact of the music.
Press the MUSIC TRIG- button (LED shines) and the sound-control is activated.
Strobe-function
Via the STROBE-button, you can strobe all fixtures at the same time (You can strobe PAN or TILT position too).
Manual controll of the fixtures
If LED-diode of some FIXTURE button shines, the fixture responds to a joystick movement.You can also change
the desired value by pressing the FUNCTION button and the UP/DOWN- buttons on DMX VALUE-DISPLAY.
The function which was changed, does not respond to the running program (function is excluded).
To return the fixture to the program, press the respective FIXTURE button and shortly the PROGRAM- button.
The FIXTURE-LED will switch off, fixture is returned to the program and at the same time the LED diodes of
FIXTURES, which are chosen from the program, will shine.
To return all fixtures to the program, press shortly twice the PROGRAM button.
Programming
Choose one of the freely programmable chasers between 21 and 30 with the PROGRAM UP/DOWN buttons.
Press and hold the PROGRAM button until its LED flashing. The PROGRAM-DISPLAY shows number of the
programmed steps and STEP-LED shines. Now you can set the values of DMX channels for the current step.
Press the TIME button and set time on the PROGRAM-DISPLAY. The TIME-value can be between 0 and 5 sec.
This value is the minimum period of last program step in SLOW and MEDIUM mode (waiting on the termination of
PAN and TILT movement). The value TIME will be immediately be carried out in the FAST mode (without waiting
on the termination of PAN and TILT movement).
Creation of the program
By pressing ENTER- button, the current step is written into memory and simultaneously it is replicated into next
step. The STEP-LED shines and the new step is shown.You can repeat this procedure as requested.The maximum
number of programmable steps per program is 32.
Modification of the program
In order to enter the programming-mode, press and hold the Program and ENTER-button until the Program-LED is
shining. Now you can modify the program.
By pressing the STEP-button, the change is written into memory and the PROGRAM-DISPLAY shows the number
