24
This option should be set "OFF" for all slaves in the master/slave chain by reason of the right program starts.
For example:You have selected program "PrG.3" in this menu and:
this fixture is set as a single fixture (master/slave or controller operating)- the fixture will run its program "PrG.3".
this fixture is set as a master in a data chain- the fixture will run its program "PrG.3".
this fixture is set as a slave in a data chain- the fixture will run its program according to the master(if the master
runs its own program "PrG.1", the slave will run its own program "PrG.1"also).
Note:If the fixture operates in the controller mode ( DMX controller is connected) and any program from this menu
is selected ,in this case the fixture will not respond to the DMX controller after switching On and will play selected
program.
Playing program
This function allows you to run a bilt-in program "tESt" and the 3 freely-programmable programs
"PrG.1,PrG.2,PrG.3" .Press [Up] or [Down] buttons to select the desired program and press [Enter] to run the
program which will be played continuously in a loop.
If you want to pause the runnnig program in the required position, press the [Enter]-button(messages"PAUS"/"
program No."blink ).To continue the program running,press the [Enter]-button again.
Note:If the fixture operates in the controller mode ( DMX controller is connected) and any program from this
function is selected in this case the fixture will not respond to the DMX controller and will play selected program.
You can't play programs on the slave fixtures from their control panels if the master fixture is switched On and
connected to the slaves (playing is forced by the master).
Editing program
This menu item allows you to select a program to edit or create.The SPOT 575 XT has one built-in program
("tESt") and the 3 free programs,each up to 99 steps.
If the fixture is set as a master ,then you may edit any program in the slaves.You can't edit programs on the slave
fixtures from their control panels if the master fixture is switched on and connected to the slaves (editing is
possible by the master control panel only).
Procedure:
1. Press [Up] or [Down]-button to select the program you want to edit ("PrG.1" - "PrG.3") and press [Enter].
2. Press [Up] or [Down]-button to select the desired fixture ("MASt." - "SLA.9") and press [Enter]-button.
3. Press [Up] or [Down]-button to select the desired program step ("St.01" - "St.99") and press [Enter]-button.
4 Press [Up] or [Down]-button to select the desired item and press [Enter]-button.Now you can edit by [Up] or
[Down] buttons the DMX value for selected item:
"P.End." -
a total number of the program steps,value 1-99 .This value you must set before start
programming(e.g. if you want to create program with the 10 steps,set the value onto 10).
"PAn" -
a pan,value 0-255
"tilt" -
a tilt,value 0-255
"F.PAn" -
a fine pan, value 0-255
"F.tilt" -
a fine tilt,value 0-255
"SPEd" -
a speed of PAN/TILT movement,value 0-255
"Col1" -
a colour- wheel 1, value 0-255
"Col2" -
a colour- wheel 2, value 0-255
"Pris" -
a prism,macros,value 0-255
"S.Gob" -
a static gobo,value 0-255
"r.Gob." -
a rot.gobo,value 0-255
"G.rot." -
a rot. gobo rotation,value 0-255
"IriS" -
a iris,value 0-255
"Foc." -
a focus ,value 0-255
"Stro." -
a strobe,value 0-255
"dimr" -
a dimmer, value 0-255
"S.tim." -
a step time,value 0,1-25,5 seconds
"COPY." -
a copying the current prog. step to the next prog. step .If the last prog.step is copied to the
next prog. step ,parameter "P.End" is increased about 1 by itself (except step 99).
5. Press Enter]-button to confirm adjusted value .
6. Press [Mode]-button,select next prog. step and repeat this procedure (steps 4 and 6).
courtesy of
www.sxsevents.co.uk
Phone: 0870 080 2342
email: [email protected]
Event production and Audio-Visual Services
www.sxsevents.co.uk
