Robe Robin 100 LEDBeam Wireless DMX CRMX, Руководство пользователя

Страница: 26 / 38

6
6.4 Manual Control (Manual)
Pres Eff - Preset effects . Use the menu to show preset positions of each channel effect.
Manual C - Manual control . Use the menu to control all fixture channels by means of the control panel.
6.5 Test program (Test Prg)
Use this menu to to run a special demo-test sequences without an external controller, which will show you some
possibilities of using Robin 100 LEDBeam.
Static
-
Static mode
. This mode is suitable for projections on the wall, ceiling or ground
without any head movement.
Dynamic
-
Dynamic mode.
This mode uses all Robin 100 LEDBeam functions including
pan/tilt movement and therefore is good for a complete introduction of the fixture.
6.6 Stand-alone (St Alone)
Music T - Music trigger . Select this function to enable the sound control of the running program via the built-in
microphone.
Auto Run - Presetting playback . This function allows you to select the program which will be played in the
stand-alone mode after switching the fixture on. Selected program will be played continuously in a loop.
Off
- The option disables „Auto Run” function.
Test
- The option will start built-in test program.
Prog 1
- The option will start user-created program 1
Prog 2
- The option will start user-created program 2
Prog 3
- The option will start user-created program 3
Pr Play
-
Playing program
. Select this menu to run a user-created program in a loop.
Test Prg - The option runs built-in test program.
Prog 1 - The option runs user-created program 1
Prog 2 - The option runs user-created program 2
Prog 3 - The option runs user-created program 3
Select the program you wish and press [ENTER]. The selected program starts running. By Pressing [ENTER]
again, program pauses running.
Pr Edit - Editing program . Select this menu to edit or create the program. The Robin 100 LEDBeam has one
built-in program and one user-editable program up to 40 steps. Each program step has a step time - during
which effects last in the current step and a fade time- during which effects move to new positions.
To edit program:
Procedure:
1. Press [NEXT] or [PREV] to select the menu "Edit" and press [ENTER].
2. Press [NEXT] or [PREV] to select the desired program step and press [ENTER] button.
3. Press [NEXT] or [PREV] to select the desired item and press [ENTER] button. Now you can edit by [NEXT]
or [PREV] buttons the DMX value (0-255) for selected item:
Prg End. a total number of the program steps (value 1-40). This value you should be set before
starting of programming (e.g. if you want to create program with the 10 steps,
set Prg End=10).
PAn a coarse pan movement CTC a colour temperature correction
PAn F a fine pan movement Virt C a virtual colour
Tilt a coarse tilt movement Strob a strobe/shutter
Tilt F a fine tilt movement Dimmer a dimmer coarse
P/T Sp a pan/tilt speed Dimm F a dimmer fine
Power power/special functions F.Tim a fade time (0-25.5 sec)
R Led 1 (2/3) red coarse -zone 1 (2,3) S.Tim a step time (0-25.5 sec)
G Led 1 (2/3) green coarse - zone 1(2,3) COPY copying the current prog. step to
B Led 1 (2/3) blue coarse - zone 1(2,3) the next prog. step
W Led 1 (2/3) white coarse - zone 1(2,3)
4. Press [ENTER] button to confirm adjusted value .
5. Press [ESCAPE] button, select next prog. step, press [ENTER] button and repeat steps 3 - 5).