roal RCB1200 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 33

roal RCB1200 Скачать руководство пользователя страница 25

25

The RCB1200 power supply is designed to be used as part of an end-system in a restricted environment and therefore should
only be accessible to qualified and trained personnel. Persons attempting to configure a unit must have the necessary
knowledge and training before doing so. Incorrect configuration may cause damage to the power supply and may affect its
warranty.

Output power modules (OP-A, OP-B, OP-C, OP-D) may be added, replaced or moved by strictly following the sequence of
operations described here below.
Please contact ROAL Electronics or your distributor for assistance in configuring your power supply.

Step 1:
Remove the AC input line connection and all other connections from the power supply. Remove the unit from the system if
there has been previously installed.

WARNINGS!

Leave the unit to stand for a minimum of 3 minutes after removing all power and other connections from the unit before
attempting to configure or re-configure the power supply.

Always remove the power supply before handling. During operation, the external surface of the unit can become hot.
Leave the unit to stand for 10 minutes for cooling down before handling.

Dangerous voltages are present within the power supply. Covers may only be removed by qualified personnel when the
power supply has been disconnected from the mains supply voltage for more than 3 minutes. Covers must be replaced
and all screws secured properly before reconnecting to the mains voltage.

Step 2:

Remove the four screws that secure the hinged lid to the chassis.

C

ONFIGURING YOUR

P

OWER

S

UPPLY

DISTRIBUTED BY TEXIM EUROPE

«
...
23
24
25
26
27
...
»

Содержание RCB1200


































Отзывы:

Нет отзывов