RNA ESK 2002 Скачать руководство пользователя страница 16

Страница: 16 / 23

Rhein-Nadel Automation GmbH

VT-BA-ESK2002_EN-2020 / 06.05.2020 SJ

5.5.3. Code C012 for channel 3, (feed rate output 3, vibratory or conveyor drive)

Objective:

Setting

and limiting the vibration amplitude, external enabling, soft start delay and soft stop delay, and the

vibratory or belt feeder function.

Select code

Set code

Code C002

Set vibrating amplitude

Only in controller mode

0 - 100 %

Limit vibrating amplitude

50 - 100 % (*)

External enabling

I = active
0 = not active

External enabling signal direction

I = Start = 24V DC
0 = Stop = 24V DC

Soft start delay

0 - 5 sec.

Soft stop delay

0 - 5 sec.

Switching to vibratory or belt feeder

0 = vibratory drive
1 = belt feeder

Return

Save and return to
main menu

(*) For RNA feeders with 200 V magnets = 90 %

5.5.4. Code C003 Seal setpoint

Objective:

Sealing-in

the setpoints in the main menu. A direct change of the values is no longer possible. You can

only make any changes now through code C001, code C002 and code C012.

Select code

Set code

Code C003

Setpoint (vibrating amplitude)

1 = adjustable
0 = input inhibited

Return

Save and return to
main menu

5.5.5. Code C004 sensor input 1 and code C005 sensor input 2

Objective:

Activating and setting the sensor inputs

Select code

Set code

Code C004

Sensor 1 input

I = active
0 = not active

Invert input signal direction

I = Start = 24V DC
0 = Stop = 24V DC

Delay of sensor status
CLEAR,

Start delay.

0 - 60 sec.

Delay of sensor status
OPERATED,

Stop delay.

0 - 60 sec.

Return

Save and return to
main menu

Same applies analogously to code

C005

(sensor input 2).

KANAL l
KANAL 2

CODE

KANAL l
KANAL 2

CODE

KANAL l
KANAL 2

CODE

KANAL l
KANAL 2

CODE

KANAL l
KANAL 2

CODE

KANAL l
KANAL 2

CODE

KANAL l
KANAL 2

CODE

KANAL l
KANAL 2

CODE

KANAL l
KANAL 2

CODE

KANAL l
KANAL 2

CODE

KANAL l
KANAL 2

CODE

KANAL l
KANAL 2

CODE

KANAL l
KANAL 2

CODE

KANAL l
KANAL 2

CODE

KANAL l
KANAL 2

CODE

KANAL l
KANAL 2

CODE

KANAL l
KANAL 2

CODE

KANAL l
KANAL 2

CODE

KANAL l
KANAL 2

CODE

KANAL l
KANAL 2

CODE

KANAL l
KANAL 2

CODE

Содержание ESK 2002
























Результаты поиска

Содержание ESK 2002

Отзывы:

Похожие инструкции для ESK 2002

Бренды по названию

Популярные бренды

RNA ESK 2002, Руководство по эксплуатации

Результаты поиска

Содержание ESK 2002

Отзывы:

Похожие инструкции для ESK 2002

Бренды по названию

Популярные бренды