RKI Instruments 65-2321RK Скачать руководство пользователя страница 19

Страница: 19 / 19

65-2321RK Oxygen Transmitter • 15

Parts List

Table 3 lists replacement parts and accessories for the oxygen transmitter.

Table 3: Parts List

Part Number

Description

06-1248RK-03

Calibration kit sample tubing, 3 foot length

07-0039RK

Detector housing cap gasket

18-0400RK-01

Junction box with rubber spacers

57-1064RK-01

S2 series oxygen amplifier, w/orienting gasket, 0 - 25%

65-1025RK

Oxygen plug-in sensor

65-2494RK

Oxygen replacement detector assembly, includes plug-in sensor

71-0175RK

65-2321RK Operator’s Manual (this document)

81-0076RK

Zero air calibration cylinder, 17 liter steel

81-0076RK-01

Zero air calibration cylinder, 34 liter steel

81-0076RK-03

Zero air calibration cylinder, 103 liter steel

81-0078RK

100% nitrogen calibration cylinder, 17 liter steel

81-0078RK-01

100% nitrogen calibration cylinder, 34 liter steel

81-0078RK-03

100% nitrogen calibration cylinder, 103 liter steel

81-F301RK

Calibration kit for oxygen detector head, 103 liter

81-F301RK-LV

Calibration kit for oxygen detector head, 34 liter

81-1050RK

Regulator with gauge and knob, 0.5 LPM, for 17 liter and 34 liter steel calibration cylinders

81-1051RK

Regulator with gauge and knob, 0.5 LPM, for 34AL/58/103 liter calibration cylinders

81-1117RK

Calibration cup

www.calcert.com

[email protected]

1.800.544.2843

Содержание 65-2321RK




















Результаты поиска

Содержание 65-2321RK

Отзывы:

Похожие инструкции для 65-2321RK

Бренды по названию

Популярные бренды

RKI Instruments 65-2321RK, Руководство оператора

Результаты поиска

Содержание 65-2321RK

Отзывы:

Похожие инструкции для 65-2321RK

Бренды по названию

Популярные бренды