Rivers Edge LANDMARK LM601 Скачать руководство пользователя страница 20

Страница: 20 / 28

Check for parts online at

www.HuntRiversEdge.com

or call 800-450-EDGE (3343) M-F 8-5

Operator's Manual

Landmark

™

Permanent Blind

FIGURE 20

13. Locate the three horizontal window panels with shooting rail sleeves (27) and the three S1 poles. Insert an S1 pole into the

shooting rail sleeve on each window panel. SEE PARTS BREAKDOWN (Page 25).

14. Locate the other three horizontal window panels (28) and the six vertical window panels (35).

NOTE: SET ASIDE THE TWO DOOR PANELS (34) FOR NOW. THEY ARE LONGER THAN THE HORIZONTAL WINDOW PANELS.

15. Attach a horizontal window panel with shooting rail (27) to one of the window openings by connecting the clips to the lower

half of the window poles.

MAKE SURE THE SHOOTING RAIL IS ON THE TOP.

Attach a horizontal window panel (28) to the top half

of the same window poles. SEE FIGURE 20.

NOTE: THE TETHER BUCKLE SHOULD BE LOCATED IN THE LOWER LEFT OF THE BOTTOM HORIZONTAL WINDOW PANEL WITH

SHOOTING RAIL AND THE UPPER LEFT OF THE TOP HORIZONTAL WINDOW PANEL.

16. On the same window opening, attach two vertical window panels (35) by connecting the clips to the right and left sides of the

top frame pole and mid frame pole. SEE FIGURE 21.

NOTE: THE TETHER BUCKLE SHOULD BE LOCATED ON THE TOP OF BOTH VERTICAL WINDOW PANELS.

17. Repeat Step 15-16 for the other two windows.
18. Attach the two door panels (34) by connecting the clips to the vertical poles of the two front wall panels.

NOTE: THE TETHER BUCKLE SHOULD BE LOCATED IN THE LOWER RIGHT OF THE BOTTOM DOOR PANEL AND IN THE UPPER LEFT OF

THE UPPER DOOR PANEL.

NOTE: SLIDE CLIPS OF LOWER DOOR PANEL DOWN AND SLIDE CLIPS OF UPPER DOOR PANEL UP TO CREATE DOOR OPENING.

WHEN IN USE, SLIDE TO WANTED GAP FOR USE AS FOURTH WINDOW.

FIGURE 21

Tether Buckle

Shooting R

ail

Tether Buckle

Clip

Window Pole

Top Frame

Pole

Clip

Tether Buckle

Mid Frame

Pole

Содержание LANDMARK LM601





























Результаты поиска

Содержание LANDMARK LM601

Отзывы:

Похожие инструкции для LANDMARK LM601

Бренды по названию

Популярные бренды

Rivers Edge LANDMARK LM601, Руководство оператора

Результаты поиска

Содержание LANDMARK LM601

Отзывы:

Похожие инструкции для LANDMARK LM601

Бренды по названию

Популярные бренды