Rivers Edge LANDMARK LM601 Скачать руководство пользователя страница 18

Страница: 18 / 28

Check for parts online at

www.HuntRiversEdge.com

or call 800-450-EDGE (3343) M-F 8-5

Operator's Manual

Landmark

™

Permanent Blind

7. Hang the left front wall panel (31) on the front side of assembled steel frame by connecting the top clip of the pole to the top

of the frame near the K1 brace. Connect the bottom clip of the pole to the bottom frame by angling the pole towards the center of

the door opening, and once attached, sliding outwards towards F1 brace. Repeat for right front wall panel (30). Secure the top and

bottom D-ring strap and the hook and loop straps for each front panel to assembled steel frame. SEE FIGURE 18.

8. Secure the two front wall panels to the side wall panels by matching up the hook and loop attachment strips in the two front

corners.

TIGHTEN D-RING STRAPS TO ASSIST IN LINING UP HOOK AND LOOP ATTACHMENT STRIPS.

Start at the top and work your

way to the bottom. Adjust and redo as necessary to accomplish a snug fit and take out as much slack in the wall panels as possible.

SEE FIGURE 18A.

9. Repeat for the back two corners of the blind.

NOTE: WITH THE CORNER ATTACHMENT COMPLETE IN ALL FOUR CORNERS, MAKE SURE ALL D-RING STRAPS ARE TIGHT TO THE FRAME.

FIGURE 18

D-ring Strap

Hook and

Loop Strap

Содержание LANDMARK LM601





























Результаты поиска

Содержание LANDMARK LM601

Отзывы:

Похожие инструкции для LANDMARK LM601

Бренды по названию

Популярные бренды

Rivers Edge LANDMARK LM601, Руководство оператора

Результаты поиска

Содержание LANDMARK LM601

Отзывы:

Похожие инструкции для LANDMARK LM601

Бренды по названию

Популярные бренды