RiTTO TWINBUS Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 197

background image

Inst

alla

tion

Installation: Assembly, connection and start-up

38

Delete settings

This function deletes all settings and programmed bell buttons. If necessary, please note down any existing customer
settings before deleting the settings.

If the settings have not been deleted:

Check on the TwinBus power supply unit whether the setting protection is activated - see page

Repeat the procedure.

2.5.2 TwinBus comfort indoor telephone 1 7650

Assembly

Remove the TwinBus device and the supplied components from the packaging.

Please provide your customers with a copy of the operating instructions for the TwinBus device. The operating
instructions are printed on the packaging or are enclosed with the unit.

Activity

Result

✔

Short tone: Settings have been deleted.

/

Long tone: Settings have not been deleted.

Press and hold for 5 s
until

+

Acoustic signal for confirmation

!

00037-0

«
...
36
37
38
39
40
...
»

Содержание TWINBUS






































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TWINBUS

Бренд: SCS Sentinel Страницы: 170

Бренд: National Instruments Страницы: 23

Бренд: TCS Страницы: 28

Бренд: Panasonic Страницы: 20

Бренд: Rainbow Страницы: 26

Exubera Pro UC EV9333-50

Бренд: Everpure Страницы: 2

Megavox Pro MEGA-6000U1

Бренд: Anchor Страницы: 1

Бренд: Beta Three Страницы: 11

Бренд: TCL Страницы: 48

Бренд: salmson Страницы: 195

AeGIS 8000 PLUS

Бренд: PACH & COMPANY Страницы: 30

Бренд: Vidos Страницы: 8

Бренд: Benwin Страницы: 7

Бренд: Eaton Страницы: 2

Бренд: DAPAudio Страницы: 13

Powerbox PA 802

Бренд: Conrad Страницы: 4

Бренд: Chamberlain Страницы: 4

Бренд: FAAC Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды