qtm9322b.pm5
For assistance, call RITRON at 1-800-872-1872, or go to < http://www.ritron.com >
Page 4
What is my Radio System Frequency? Ritron pioneered
the Color Dot system to simplify the identification of radio
system frequencies for Ritron Jobcom radios. Color Dots
are placed on the bottoms of and inside the enclosures of
all Jobcom radios. Other manufacturers have also adopted
this idea.
To identify your assigned frequency if your radios do not
have a color dot, locate a label identifying the receiver
frequency in megahertz (MHz). Your assigned frequency is
also shown on your F.C.C. Station License. Call your radio
dealer or Ritron for help if you cannot determine your
radio's receiver frequency.
Do I need to program my Quick Talk's transmitter
frequency? The original factory-programmed transmitter
frequency of your Quick Talk is marked on the outside of
the shipping box, and is also indicated by a color dot on the
inside the unit case. If the Quick Talk frequency matches
your radio system frequency, and if the Quick Talk has not
been reprogrammed since it left the factory, you may skip
this section and proceed to the next.
TO PROGRAM THE QUICK TALK TRANSMITTER
FREQUENCY:
a. Determine the frequency of your radio system.
b. Find your frequency in the appropriate table at right,
and determine its corresponding two digit code. If
your radio system frequency is not in the chart, your
Quick Talk must be programmed by a radio dealer
or by Ritron.
c. Pick up the telephone receiver, and listen for the
acknowledge tone. Dial "11", then the digits of the
selected frequency code from the table.
Examples: If the Quick Talk is a VHF RQT-150
model, and the radios operate on
154.570 MHz (Blue Dot frequency),
dial "11-02".
If the Quick Talk is a UHF RQT-450
model, and the radios operate on
467.925 MHz (Blue Star frequency),
dial "11-08".
d. Quick Talk responds with a single beep to indicate it
has programmed the transmitter frequency.
e. You may either hang up or continue programming.
NOTES: If you make a dialing mistake while program-
ming, hang up the telephone handset, then
pick it up and dial again.
If you reprogrammed the Quick Talk frequency,
you may wish to remove the Color Dot from
inside the case, to avoid later confusion.
What the Tones (Beeps) in Your Earpiece Mean:
•
A series of three short tones cues you to begin
recording a message.
•
A single brief tone means your command is
accepted and stored.
•
A series of long repeating tones means your
command was not understood; hang up and dial
again.
UHF Business Band
Model RQT-450
MHz
Frequency Color
QUICK
TALK
FREQ. CODE
01
154.600 .... Green Dot
02
154.570 .... Blue Dot
03
151.625 .... Red Dot
04
151.955 .... Purple Dot
05
151.925
06
154.540
07
154.515
08
154.655
09
151.685
10
151.715
11
151.775
12
151.805
13
151.835
14
151.895
15
154.490
16
151.655
17
151.745
18
151.865
VHF Business Band
Model RQT-150
MHz
Frequency Color
QUICK
TALK
FREQ. CODE
01
467.7625 ..... J
02
467.8125 ..... K
03
464.5500 ..... Yellow Dot
04
464.5000 ..... Brown Dot
05
467.8500 ...... Silver Star
06
467.8750 ...... Gold Star
07
467.9000 ...... Red Star
08
467.9250 ...... Blue Star
09
469.2625
10
462.5750 ...... White Dot
11
462.6250 ...... Black Dot
12
462.6750 ...... Orange Dot
13
464.3250
14
464.8250
15
469.5000
16
469.5500
17
463.2625
18
464.9125
19
464.6000
20
464.7000
TABLE 1: TRANSMIT FREQUENCY CODES
PROGRAMMING YOUR QUICK TALK TRANSMITTER FREQUENCY
(VHF Business Band)
(UHF Business Band)
