background image

 

 
Section 3

 

Programming 

20

  

3.7 

Program the NOAA Weather Frequency 

The LM-V150 can be programmed to play severe weather warnings originating from the National Weather service 

that are broadcast on one of seven NOAA weather frequencies.  The Loudmouth

 is shipped from the factory 

without a NOAA weather frequency selected.  Before the Weather Alert feature can be used you must first select 

the local NOAA frequency.  

 

1. Press 

and 

HOLD

 the 

PROGRAM

 button (See 

Loudmouth

 receiver assembly

 on page 2 

for location). A "P" will appear on the program display as you enter program mode and the 

radio will beep rapidly. 

2. Release 

the 

PROGRAM

 

button after the beeping has stopped. The radio will emit a triple 

beep indicating that the radio is in program mode and a hyphen will appear on the program 

display. 

3.  Scroll to the character “d” by clicking the 

PROGRAM

 

button until the program display 

shows the correct character. 

Pause

—the radio will sound a low tone and show a hyphen 

across the center of the display to indicate that it is ready to accept the NOAA Weather 

Frequency code.   

4.  Enter the Weather Frequency code by clicking the 

PROGRAM

 

button until the program 

display shows the desired number. 

Pause

—the radio sounds a low tone and will begin 

playing the NOAA weather broadcast over the Loudmouth

 speaker.  Monitor the channel 

for a few minutes to be sure it is the broadcast for your local area. 

5.  Press and release the 

ENTER

 button to save your programming. A triple beep will sound to 

indicate that programming was successful and a hyphen will appear on the program 

display.  The radio is now ready for another program entry. 

 

NOTE:  An error tone will sound if you attempt to save an incorrect code, an "E" will appear 

on the display.  Check the digits you are attempting to enter, then re-enter.   

6.  Once you have made your final program entry, press the 

ENTER

 button a final time to exit 

programming mode.  The Program display will be blank and the radio will be ready for use.  

The Loudmouth

 will exit program mode automatically after 30 seconds if no program 

entries are attempted. 

 

 

 

Table 6:  NOAA Weather Frequency Codes 

 

 

Code

 

Frequency

 

 1 

162.400 

MHz 

 2 

162.425 

MHz 

 3 

162.450 

MHz 

 4 

162.475 

MHz 

 5 

162.500 

MHz 

 6 

162.525 

MHz 

 7 

162.550 

MHz 

 

 

A complete list of NOAA weather frequencies available in your area can be found at 

http://www.weather.gov/nwr/nwrbro.htm

 

 

Содержание AIERIT27-150






























































Отзывы: