RITE-HITE 4487000001, Руководство пользователя

Страница: 26 / 40

SHR-5000™ Dok-Lok
®
Owner's Manual
Rite-Hite
®
26 Publication:
AMEN00096 2018-05-30
TROUBLESHOOTING
LED Status Chart
? = Varies (per operation)
* = On for 15 sec before M2 energizes
A = Alternating
D = Double fast pulsing / flashing
F = Off
ITL = Interlock input on
K = Continuous slow chirp
M = Lights when button pressed
P = Pulsing / Flashing
(set to steady using DIP switches)
T = Steady On
MICRO CONTROL BOARD POWER BOARD
INPUTS OUTPUTS
FIELD PUSH BUTTONS 12VDC RELAY 115/230VAC
Dok-Lok Limit Switch 1 [SW1] Dok-Lok Limit Switch 2 [SW2] Unlock Interlock [UNLK ITL] Lock Unlock Horn Silence (1/2/3) Inside Red Light [ISR] Inside Green Light [ISG] Corner-V
u Red Light [CVU RD]
Corner-V
u Green Light [CVU GRN]
Leveler-V
u Red Light [L
VU RD]
Leveler-V
u Green Light [L-VU GRN]
Outside Red Light [OSR] Outside Green Light [OSG] Dok-Lok Horn [HORN] Restraint Overload LED [YELLOW] K1 - Green Light Interlock K2 - Security System Interface [IF EQUIPPED] Motor Ouptut #1 [M1/LOCK] Motor Ouptut #2 (M2/UNLOCK) 12VDC Power Supply OK
TERMINAL BLOCK NO. J131 J132 J143 Membrane J716 J717 J121 J122 J123 J124 J112 J111 J719 N/A J93 J103 J54 J53 J21-6
POWER BOARD LEDS – – – – – – – – – – – – – – – – – – LD2 LD1 LD7
MICRO CONTROL BOARD LEDS
LD20 LD23 LD30 LD52 LD17 LD19 LD11 LD13 LD18 LD12 LD49 LD48 LD15 LD50 LD9 LD10 LD1 LD3 –
NO.
010100
State/Sequence No
Locked State
F T ? – – – F P F P F P P F F F T T F F T
010101 Locking Sequence T T ? M – – T F P F P F P F F F F T T F T
010200 Unlocked State T F ? – – – P F P F P F F P F F F T F F T
010201 Unlocking Sequence T T ITL – M – T F P F P F P F F F F T * T T
010400 Fault State T T ? – – – P F P F P F P F P F F F F F T
010401 Fault Silenced State T T ? – – M A A A P F F F T T F F T
010500 L/S Fault State Lock F F ? – – – D F D F D F P F D F F F F F T
011100 Overload Fault State ? ? ? – – – P F P F P F P F K T F F F F T
RESET PROCEDURE:
Motor Overload Fault State (Amber LED LD50 is illuminated and the Dok-Lok horn is slowly chirping)
1
Press and hold Horn Silence Button (3-Button System)/Horn Silence #2 Button (5-Button System) until Horn Chirps (≈ 5 Seconds). Or
2 Press and Release Restraint O/L Button on Micro Controller Board
When the motor overload has been reset, the Yellow LD50 LED will turn off and normal operation resumes If Dok-Lok motor does not run after resetting the overload, check Motor Fuse 10FU1