background image

4

material used for final assembly, no liability shall be assumed nor accepted for 
any damage resulting from the use by the user of the final user-assembled product. 
By the act of using the user-assembled product, the user accepts all resulting 
liability. If the buyer is not prepared to accept the liability associated with the use 
of this product, the buyer is advised to return this kit immediately in new and 
unused condition to the place of purchase.

To make a warranty claim, send the defective part or item to Hobby Services at 

this address.

Hobby Services

 217-398-8970 

ext#6

3002 N. Apollo Dr., Suite 1 

[email protected]

Champaign, IL  61822 USA

Include a letter stating your name, return shipping address, as much contact 
information as possible (daytime telephone number, fax number, e-mail address), 
a detailed description of the problem and a photocopy of the purchase receipt. 
Upon receipt of the package the problem will be evaluated as quickly as possible.

FEATURES

  Entry Level 250 class racing quad

  Oneshot125 speed controls

  2280kV 1806 size Brushless motors

  Ready to Fly, no building required

  Flight Controller is pre-programmed, no setup needed

DIMENSIONS

 

Size:

 250mm (9.8in) diagonally motor to motor

 

Width:

 241mm (9.5in)

 

Length:

 252mm (9.9in)

 

Height:

 69mm (2.7in)

 

Prop:

 5 x 4.5

 

Blade Length:

 127mm (5in)

 

Empty Weight:

 502g (17.7oz.) 

without battery

FPV VTX Antenna

FPV Camera

Memory Card Slot

  600TVL FPV Camera

  200mW or 25mW VTX

  On Board DVR

CONTENTS

  RTF RISE VUSION FPV RACER

  Transmitter

  FPV Goggle with Monitor

  Monitor Antenna

  Goggle Foam Liner

  1500mA 3S LiPo

  LiPo Charger w/AC Adapter

Содержание FPV RACER

















Отзывы: