background image

6

 

Wireless Sounder Instructions

 

 

Muting Tamper  

This feature disables a tamper alarm from the sounder and it is recommended to be 
used when replacing sounder's batteries.  

 

NOTES:

 

1. An ongoing tamper alarm will not be disabled.  
2. 

WisDom:

  This  feature  is  controlled  under  the  Engineer  Menu  (Quick  key  [9][2][5]).  Tamper  alarm  

    will be disabled during the current installation programming period. 
3. 

Agility:

 Grandmaster Code/User Menu > Activities > Advanced > Service Mode (Agility 3 only) 

    The tamper alarm will be disabled for the time programmed in the Mode Service timer. 
4. 

LightSYS  (V2.40  and  above):

  Grandmaster  Code/User  Menu  >  Activities  >  Advanced  >  Service 

Mode 
    The tamper alarm will be disabled for the time programmed in the Mode Service timer. 

Setting Supervision Time 

Specifies how often the system generates a supervision request to the sounder. 
If any of the sounders does not respond to the request at least once, during the 
receiver supervision time, the system will regard the accessory as lost. 

 

NOTE:

 

The receiver supervision time should be higher than the sounder supervision time in order to eliminate 
false lost event. 

Range: 00-255 minutes 
Default: 58 minutes 

 

NOTE: 

WisDom:

 Engineer menu: 1) System > 1) Timers > 9) Accessory supervision time 

Agility:

 Engineer menu: 1) System > 1) Timers  > TX supervision 

LightSYS (V2.40 and above):

 Engineer menu: 1) System > 1) Timers  > 6) Wireless > 3) TX supervision 

Pre Alarm indication 

This wireless sounder incorporates a pre - alarm feature that enhances the security of 
the system, by producing a local alarm in case of sabotage. 
If defined, the system sends a pre-alarm signal to the sounder at the beginning of the 
entry delay. If the sounder does not receive a cancellation signal from the system at 
the end of the entry time, the sounder goes into alarm mode. 

 

NOTE: 

WisDom (Ver 4.25):

 Engineer menu Quick key 1) System > 2)Controls > 44) Pre alarm 

Agility:

 Engineer menu  [1][2] > Advanced > Sounder Pre alarm 

LightSYS (V2.40 and above):

 Engineer menu 1) System > 2) Controls > 7) Device > 5) Sounder Pre 

alarm 

Содержание WL S42













Отзывы: