RIOT PLANES Sea Monkey Скачать руководство пользователя страница 22

Страница: 22 / 23

Optional Amphibious Kit

The amphib kit lets you fly your Sea Monkey

from a smooth surface (gym, pavement or short

grass).

It allows you to drive into the water to take off,

and drive out after landing!

Drill a 1/8 inch hole in the fuselage in the corner

where the two bottom skis meet. Use a long drill

bit or a piece of 1/8 brass tubing.

Slide the carbon axle housing in place. Center

this, and apply two blobs of hot glue over the

housing and onto the foam.

Make these on both sides of the fuselage.

Using hot glue, attach the steel axles into the

housing so that about 3/8 inch sticks out.

When cool, slip on a wheel and a plastic washer.

Secure with a tiny dab of hot glue.

You are now ready to take off and land almost

anywhere!

Thank you for purchasing this kit!

We hope you enjoy many relaxing flights with

your Sea Monkey.

When you are ready for another outstanding

flying model, why not check our other planes at

www.riotplanes.com

Содержание Sea Monkey
























Результаты поиска

Содержание Sea Monkey

Отзывы:

Похожие инструкции для Sea Monkey

Бренды по названию

Популярные бренды

RIOT PLANES Sea Monkey, Инструкция по сборке

Результаты поиска

Содержание Sea Monkey

Отзывы:

Похожие инструкции для Sea Monkey

Бренды по названию

Популярные бренды