RioOutdoors 4S-WPH Скачать руководство пользователя страница 10

Страница: 10 / 41

10 |

P a g e

1.7

OVERALL PERGOLA SIZE

We have designed the corner elbow brackets to provide automatic alignment of the floor floating s and the header s. By

making certain all outer perimeter “Header Lengths” are of the same length, following the instructions properly, and

securing the s to the elbow brackets as instructed, you will achieve a perfect hexagonal floating deck base for your pergola.

All you have to do is determine the size you desire for your pergola. See table, below, for Living Area based on the Header

Length.

We recommend a maximum header length of 12 feet for headers. Before you start assembly, study the table, below, and

determine the length of the s you will need. Remember that both the floor s and header s must be of the same lengths. The

length of the Front Frame Member is determined by the length of the other headers and are shown as DIM A, in the table

below.

HEADER

LENGTH

(in.)

DIM A (in.)

DIM B (in.)

AREA (sq. ft.)

9 ft. 8 in.

7 ft. 10 in.

11 ft. 5 in.

9 ft. 4 in.

13 ft. 2 in.

10 ft. 10 in.

106

14 ft. 10 in.

12 ft. 4 in.

139

108

16 ft. 7 in.

13 ft. 10 in.

175

120

18 ft. 4 in.

15 ft. 4 in.

216

132

20 ft. 1 in.

16 ft. 10 in.

262

144

21 ft. 10 in.

18 ft. 4 in.

312

Note: Increasing the length of the “Header Length” by 12 inches increases DIM A by, approximately, 20-3/4”. This is provided

as a general guideline to determine the outer maximum dinension of the hexagon pergola. Increasing the “Header Length”

by 12” increases DIM B , overall depth, by 18”.

Содержание 4S-WPH










































Результаты поиска

Содержание 4S-WPH

Отзывы:

RioOutdoors 4S-WPH, Руководство по установке, Страница: 10 / 41

Результаты поиска

Содержание 4S-WPH

Отзывы: