manualshive.com logo in svg

Rinstrum D841, Руководство по установке

Поделиться
Скачать
Rinstrum D841 Скачать руководство пользователя страница 12

D841/D850 Installation Manual 

 

Page 12 

 

008D-600-150 

2.7. 

Scrolling Messages  (K802 firmware in D841 Only) 

Scrolling messages are supported in the D841 using K802 firmware. The serial data 
string must be set to 9600 Baud Rate, No Parity, 8 Data Bits and 1 Stop Bit (9600 
N81)  and  be  framed  with  <SOH>  and  <ETX>.  See  Protocol  41  in  the  Protocol 
Manual for more information. 

2.8. 

Mounting Options 

Two stainless steel mounting brackets are used to mount the unit on a flat surface. 
These  brackets  are  bolted  to  rear  of  the  housing  using  the  shake-proof  nuts 
provided. The outer mounting holes are 8mm in diameter. 

 

 

Figure 12 - Mounting brackets and optional weather hood 

2.8.1.  Wall Mounting 

For wall mounting it is recommended that:  

•

  6mm or 1/4" bolts and washers be used as a minimum. 

•

  Both  Brackets  are  to  be  used  with  mounting  hole  centres  at  250mm  (9.8") 

wide and 200mm (7.9") high. Fit top bolts first to support display. 

2.8.2.  Weather Hood (Optional) 

The optional weather hoods can be used to minimise effects of direct sunlight. The 
Weather Hood mounting holes line up with the wall mounting holes on the brackets 
for easy fitment. 

Note:

  It  is  recommended  when  fitting  the  optional  weather  hood  the  two  bottom 

bolts  are  loosely  installed  first  to  support  the  remote  then  the  top  two  to  aid  in 
installation. 

Содержание D841


















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды