Rinnai REU-VAM1620W Скачать руководство пользователя

Страница: 3 / 40

V53e Outdoor Manual

Specifications

Model

V53e

Minimum Gas Consumption Btu/h

20,200 (LP) 19,000 (NG)

Maximum Gas Consumption Btu/h

120,000

Hot water capacity (Min - Max) *

0.6 - 5.3 GPM (2.3 - 20 L/min)

Hot water capacity (35°F rise)

5.3 GPM (20 L/min)

Hot water capacity (45°F rise)

4.2 GPM (16 L/min)

Two Temperature Settings (without remote controller)

120º F (49º C), default or 140º F (60º C)

Remote Controller Default Temperature Setting

104º F (40º C)

Maximum Temp Setting (with remote controller)

140º F (60º C)

Minimum Temperature Setting (with remote controller)

98º F (37º C)

Weight

34.2 lb (15.5 kg)

Efficiency Rating

0.82

Noise level

49 dB (A)

Electrical
Consumption

Normal

33 W

Standby

2 W

Anti-frost Protection

74 W

By-Pass Control

Fixed

Minimum Gas Supply
Pressure

Natural Gas

5.0 inch W.C.

Propane

8.0 inch W.C.

Maximum Gas Supply
Pressure

Natural Gas

10.5 inch W.C.

Propane

13.5 inch W.C.

Type of Appliance

Temperature controlled continuous flow gas hot water

system for residential applications.

Operation

With or without remote controls, mounted in kitchen,

bathroom, etc.

Approved Gas Type

Natural Gas or Propane - Ensure unit matches gas type

supplied at the installation location.

Connections

Gas Supply: 3/4" MNPT, Cold Water Inlet: 3/4" MNPT,

Hot Water Outlet: 3/4" MNPT

Ignition System

Direct Electronic Ignition

Electric Connections

Appliance: AC 120 Volts, 60Hz. Remote Control: DC 12

Water Temperature Control

Simulation Feedforward and Feedback.

Water Supply Pressure

Minimum Water Pressure: 20 PSI (Recommended 30-80

PSI for maximum performance)

Maximum Water Supply Pressure

150 PSI

Remote Control Cable

Non-Polarized Two Core Cable (Minimum 22 AWG)

Energy Star Qualified

Yes

Rinnai is continually updating and improving products. Therefore, specifications are subject to change without
prior notice.

The maximum inlet gas pressure must not exceed the value specified by the manufacturer. The minimum value
listed is for the purpose of input adjustment.

* Minimum flow may vary slightly depending on the temperature setting and the inlet water temperature.

Содержание REU-VAM1620W









































Результаты поиска

Содержание REU-VAM1620W

Отзывы:

Похожие инструкции для REU-VAM1620W

Бренды по названию

Популярные бренды

Rinnai REU-VAM1620W, Руководство по эксплуатации и установке

Результаты поиска

Содержание REU-VAM1620W

Отзывы:

Похожие инструкции для REU-VAM1620W

Бренды по названию

Популярные бренды