background image

Rinnai 

RDV 600_700ER IM

LOCATION

• 

When positioning the heater, the main 

variables governing the location are 

Flueing and Warm Air Distribution.

• 

This heater 

MUST NOT

 be installed 

where curtains or other combustible 

materials could come into contact with it. In 

some cases curtains may need restraining. 

Refer to the warnings on page 6 for 

clearances to furnishings, adjacent 

walls, curtains and combustibles.

• 

Mantles and surrounds can be added to 

compliment the design provided that they 

conform to the clearances shown in the 

diagrams (as shown right).

• 

The minimum clearance from the edge 

of the appliance to non-combustibles is 

150mm on the sides and 350mm above.

• 

The minimum clearance from the edge of 

the appliance to combustibles is 350mm 

on the sides and 350mm above.

• 

The depth of the mantle / surround at 

the minimum clearance may not exceed 

150mm (as shown right).

• 

An additional 100mm of clearance is required for every extra 50mm of mantle depth, i.e. for a 300mm deep 

mantle the minimum clearance is 450mm.

TV & ORNAMENTATION WARNING

CAUTION

INSTALLATION OF TV OR ORNAMENTATION ABOVE THE HEATER

The installation of electrical appliances above and in the vicinity of the heater such as, but 

not limited to, Plasma TV, LCD TV, Home Theatre Screens, Speakers, etc., 

MUST

 comply with 

their manufacturer's' instructions. It is the responsibility of the installer/end-user to check the 

installation instructions of these items and to ensure the location is suitable.
This caution also extends to, but is not limited to, ornaments such as: Paintings, Prints, 

Photographs, Tapestries, Mirrors, Stuffed Animals, etc.

Please note the recommended clearances as per the diagram above. The temperature of the wall 

surface directly above the appliance may be elevated and may discolour paint finishes or distort 

vinyl wall coverings. For durability of surfaces you should contact the relevant manufacturer for 

their specification.

WARNING

RINNAI DOES NOT TAKE ANY RESPONSIBILITY FOR ANY DAMAGE OCCURRING TO 

ANY ITEMS INSTALLED ABOVE AND IN THE VICINITY OF THE HEATER.

IDEA

Use either a shelf or mantle below the TV or ornament or alternately you can construct a recess 

to mount TV or ornament in. Check the manufacturer's installation instructions for these items 

and ensure the recess is suitable.

ENCLOSURE REQUIREMENTS

MASONRY FIREPLACE

The appliance 

MUST

 be positioned within the fireplace on a flat level surface.

If the appliance is elevated from the ground within the structure, a base 

MUST

 be constructed using suitable 

material with supporting joists capable of supporting a minimum of 1.5 times the weight of the appliance.

750mm

1000mm

(A)

(A)

Maximum mantle depth (at 350mm)  = 250mm

 

(A)

 = 150mm to non-combustibles

(A)

 = 350mm to combustibles

Note: The three sided fascia shown for illustrative purposes

350mm

GENERAL INSTALLATION INFORMATION

Содержание RDV600ER





































Отзывы: