Rinnai N-BW2 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 20

Rinnai N-BW2 Скачать руководство пользователя страница 17

Rinnai

17

Touch Wi-Fi Kit IM

7.0 WI-FI MODULE ERROR CODES

The Wi-Fi Module error codes will not disrupt operation of your appliance and may clear after some time. This error will remain visible on
your App or Networker until your Wi-Fi Module resumes operation. Table 4 details the error number, description, flashes and corrective

action. If you are unable to resolve the issue and if the problem persists contact Rinnai.

Table 4. Error Description

Networker

Error Code

Wi-Fi Operating

Indicator Flashes

Description

Corrective Action

Error Code 50

1

No configuration data detected.

Replace the Wi-Fi Module.

Error Code 51

3

Wi-Fi Module configuration error. Check SSID/password entry otherwise replace the Wi-Fi Module.

Error Code 52

3

Wi-Fi Module connection error.

Cannot connect to assigned

router after 30 seconds.

The Wi-Fi Module will try to connect to the assigned router for 3

minutes. After 30 seconds if the assigned router is not located

this error code is registered. Check router and check distance

between router and Wi-Fi Module.

Error Code 53

N/A

The Wi-Fi Module has been

forced to operate in its Default

AP State because the assigned

router could not be located.

This is the code to look for when the customer has changed their

router. The Wi-Fi Module will operate in this mode for 2 minutes

before switching back to trying to connect to the assigned router.

Error Code 54

N/A

The Wi-Fi Module has been

forced to operate in its Default

AP State because it is yet to be

configured.

This is the code to look for when the customer has not

configured their Wi-Fi Module yet. As such it will operate

indefinitely in AP mode using its default SSID/password

combination. There is no access to the networker system when

in this mode.

Error Code 55

4

Internal type 1 communication

error.

This error will not allow the Wi-Fi Module initial configuration or

system access in-house. If problem persists replace the Wi-Fi

Module.

Error Code 56

5

Internal type 2 communication

error.

This error will not allow system access in-house. If problem

persists replace the Wi-Fi Module.

«
...
15
16
17
18
19
...
»

Содержание N-BW2





















Отзывы:

Нет отзывов