background image

14 

 

TEMPERATURE CONTROLS 

Using the Temperature Controllers 
 

Press the 

ON/OFF 

button 

o n  

a  

t e m p e r a t u r e 

controller  after  making 
sure  that  water  is  not 
flowing. 
 
The  system  will  become 
active,  the  temperature 
will  default  to  40°C  and 
the  controller  that  turned 
the  system  on  will  have 
priority. 
 
The  temperature  setting 
on  the  controller  will  light 
up. 

Adjusting Temperature 
 

Simply  press 
the  Hot  Water 
T e m p e r a t u r e 
Up  or  Down 
arrow button  
 
 
 
 
 
 
until the desired 
temperature  is 
displayed  on 
t h e  

d i g i t a l 

display. 

Using Hot Water 

 
To operate the heater, simply turn any hot water 
tap  on.  This  will  automatically  light  the  burner 
providing  hot  water.  The  red 

IN  USE 

indicator 

will glow on the temperature controller. 

To turn off your hot water system 

 
During normal operation the system is left on.

 

 
To turn the system off simply press the 

ON/OFF

 

button  on  any  temperature  controller  (where 
fitted).  This  will  shut  the  water  heater  down 
completely  including  the  temperature  controller 
digital display. 
 
The Digital Monitor will go out. 
 
If hot water taps are opened when the Rinnai  is 
off, cold water will flow from the taps. 
 
If  the  system  is  to  be  left  off  over  the  winter  be 
sure  to  drain  it  down  if  there  is  a  possibility  of 
freezing temperatures. 

Using High Temperature Display Controllers 

 
You will need to program the Master controller if you want to display and use 
temperatures  over  50°C.  Programming  only  needs  to  be  done  on  Master 
universal controller; other universal controllers will not allow this. 
Deluxe  Kitchen  controllers  are  supplied  already  programmed  to  allow  high 
temperatures. 
 

STEP  1: 

On the Master controller only press and hold the 

Transfer 

and 

ON/

OFF 

buttons  simultaneously  (see  Fig.  1)  until  a  “beep”  is  heard  (approx.  5 

seconds). 

 
STEP  2:

 When the Primary controller is switched on it should be possible to select temperatures higher 

than 50ºC. If not repeat STEP 1. 

 

If  the  master  controller  is  replaced,  repeat  STEP  1  above 
for the new controller. 

Fig. 1 

NOTE

COOLER

 

HOTTER

 

Содержание INFINITY 26i





















Отзывы: