background image

LIMItEd Warranty

Warranty exclusions

the following exclusions may cause the warranty to become void and will result in a service 

charge and costs of parts (if required).

accidental damage and acts of God. 

Failure due to abuse or misuse, improper maintenance or improper storage. 

Failure due to incorrect or unauthorised installations. 

Failure or damage caused by alterations, service or repair work carried out by persons 

other than rinnai service persons or service centres. 

Where the solar collector has failed directly or indirectly as a result of poor water quality 

outside the limits specified.

 

Where it is found that there is no fault with the solar collector and the issue is related to 

the installation or failure due to lack of power supply. 

Subject to any statutory provisions to the contrary, rinnai does not accept: 

liability for consequential damage or any incidental expenses resulting from any 

     breach of the warranty, 

claims for damage to building or any other consequential loss either directly or 

     indirectly due to leaks from the solar collector or any other faults.

1.

2.

3.

4.

5.

6.

7.

a.

b.

G12/aS2 dUraBILIty

as required by the new Zealand Building Code compliance document G12/aS2, clause 7.2.3, in 

respect of the durability of the solar system components supplied by rinnai, rinnai makes the 

following statements.

The collector mounting rails have a durability of fifteen years provided they are kept clear 

of debris such as leaves. 

all other components of the system supplied by rinnai may require maintenance and/or 

replacement before fifteen years.

a.

B.

Содержание E-Frost

















Отзывы: