Daily,
carry out a general visual check, functional checks (lever, movements, etc.), and a check of the overall
condition of the rubber and metal tubing.
Check all the connections before applying pressure to any of the hydraulic circuits.
After the first two hours of work
, tighten the tools and the tube connections of the hydraulic oil system and inject
thick grease semi fluid semi fluid at lithium for transmission gears, like Mobilux EP 004 with grade industrial NLGI
00, through the greasers.
The parts of the machine not reachable without oil feeder are greased when the machine is assembled and do not need
any further maintenance.
We recommend cleaning the greasers and the grease guns before carrying out the lubrication.
The lubrication points are indicated on the machine by adhesives.
Detach the cardan joint from the tractor’s side, slide out the inner rod and grease it using the appropriate grease semi
hard at calcium for transmission gears, like Stauffer/3 with grade industrial NLGI 3; repeat this operation
every 4
working hours.
Every 8 working hours
grease the rotating joints and the pivots.
Every 16 working hours
grease the security devices and, if present, the spherical quick coupling.
Frequently check the oil levels inside the tank and if necessary fill up the oil; periodically clean the
discharge/aspiration oil filter.
Frequently change the mineral gear grease, like Mobilgear 600 XP ISO with viscosity grade VG 320, in the
bevel gears
of the rotary set, keeping the level at about cm.3 from the bottom
;
replace it
every 500 working
hours.
Check
the wear status of the tools.
Verify
that there are no broken cutters and if necessary, replace them immediately.
Replace the tines when they are worn down to 12 cm.
It is important to make sure the tines of each rotor are of equal length; it is also crucial to avoid using the equipment
with only one tine per rotor.
The tines have a right and left side version, and are lightly inclined to reduce friction with the ground.
Each rotor supports two tines of the same version, while the adjacent rotor supports tines of opposite versions.
To perform these operations only use heavy working gloves.
It is also recommended to use only original tools, requesting them from our Company or authorized Dealer.
Verify
the existence and the readability of the plates and all stickers and, if necessary, replace them with new ones.
Weekly
perform a visual inspection of all mechanism and possible loss of lubricant, of the movements and, if
necessary, grease the sliding surfaces of the moving parts to ensure functioning and reduce wear controlling also the
tubes in iron and plastic.
TRANSPORT - HOISTING - MOVEMENT
When transporting the machine be careful to block it with ropes, straps or anything suitable to keep the machine stable
and safe and to prevent accidental shifting that could cause injury or damage the machine.
If the machine has to be hoisted it must be hooked to the proper hoisting instruments by means of ropes or suitable
equipment to secure its integrity.
Before hoisting make sure that hoisting means are suitable in that they have a higher weight capacity than the weight
of the equipment.
The machine mounted on the centre of the tractor is not homologated for the transfers on common roads. So they have
to be disassemble and loaded on implements on issue and transfered by homologated trailers.
Also the machines which are more than 2.5 m. width have to be transfered by homologated trailers and longitudinal
positioned to avoid projecting parts.
The hoisting equipment must be adequate and comply with safety standards in effect at the time governing these
operations.
Verify that the instruments used are in sound condition and not worn or unsafe in anyway and above all the joints and
connections are robust, in good condition and can bear the estimated burden.
Remember that it is absolutely forbidden to remain under or in the immediate vicinity of the object whilst it is being
hoisted.
Always use thick protective gloves when carrying out these operations.
The points on the machine which are safe to attach the hoisting hooks to are indicated so by means of appropriate
adhesives.
UNISTALLATION OF MACHINE
Dismount the machine from the tractor and be careful to clean it well.
Park the vehicle on a level surface and in a safe stable way.
Store away from atmospheric agents (inside) and out of the reach of children.
DESTRUCTION AND DISPOSAL OF MACHINE
If you decide to destroy and dispose of the machine it’s recommended to render it inoperative by cutting the tubing,
disassembling knives and breaking the hydraulic motor.
Also remove identification nameplate of the machine.
Содержание 60790B
Страница 4: ......
