Rilon MIG/NBC 300GN Скачать руководство пользователя страница 8

Страница: 8 / 26

PRODUCT DESCRIPTION

The welding machine applies the most advanced inversion technology in the world.

The principle of inversion is to transform the power frequency of 50Hz/60Hz into direct current and invert it into high

frequency through high-power device IGBT, then perform voltage-drop and commutation with the output high-power D.C

power supply via Pulse Width Modulation (PWM). Since the switch power inversion technology is adopted, the weight

and volume decrease greatly while the conversion efficiency increase by more than 30%

。

Its characteristics are: stable

wire feed rate, little splatter, portable, energy-saving, low electromagnetic noise.

Our CO

gas shielded welding machine is equipped with unique electronic reactor circuit, which can precisely control the

short-circuiting transfer and mixed transfer resulted in better performance than other machines. Compared with silicon

controlled welding machine and tapped welding, our products have the following advantages: stable wire feed rate,

portable, energy-saving, electromagnetic noise free. Besides, our products spatter less, easier arc starting, deep welding

pool, high duty cycle etc. With high efficiency and energy-saving features, this equipment is applicable in large-scale

plants such as shipyards, steel structure plants etc..

Thank your for choosing our products. Please feel free to propose your valuable suggestions; we will make efforts to

perfect our products and service.

WARNING

！

The machine is mainly used for industrial purpose. It will cause radio interference indoor, operators

shall take fully preventative measures.

USER MANUAL 6 YF-20Y A1

Содержание MIG/NBC 300GN



























Результаты поиска

Содержание MIG/NBC 300GN

Отзывы:

Похожие инструкции для MIG/NBC 300GN

Бренды по названию

Популярные бренды

Rilon MIG/NBC 300GN, Руководство пользователя

Результаты поиска

Содержание MIG/NBC 300GN

Отзывы:

Похожие инструкции для MIG/NBC 300GN

Бренды по названию

Популярные бренды