Rikon Power Tools 62-450 Скачать руководство пользователя страница 14

Страница: 14 / 20

TROUBLESHOOTING

PROBLEM

LIKELY CAUSE(S)

SOLUTION(S)

Motor does

not run

1. Machine not plugged in

2. Power switch in “OFF” position

3. Power switch or cord is faulty

4. Fuse or circuit breaker are open

5. Remote control is not working

6. Remote control batteries are dead

7. Infared receiver is not working

8. Control panel ON/OFF button is

not working

9. Control panel fuse is blown

10. Motor does not work

1. Plug power cord into electrical receptacle

2. Lift switch to “ON” postion

3. Replace switch or power cord

4. Overloaded electrical circuit

5. Point remote control directly at control panel

-Make sure infared sensor on the control

panel is not blocked

-Move remote control closer to the control

panel for better direct infared signal

6. Replace batteries. See page 13 for

instruction

7. Inspect or replace control panel circuit board

8. Inspect or replace control panel circuit board

9. Replace blown fuse, see page 13 for

instruction

10. Replace motor

Motor stalls

or does not

have full

power

1. Incorrect line voltage

2. Motor capacitor has failed

3. Control panel circuit board has

failed

1. Have a qualified electrican check circuit for

proper voltage

2. Replace motor capacitor

3. Inspect or replace control panel circuit board

System has

vibration or is

noisy

1. Motor or cabinet part is loose

2. Motor fan is rubbing cover

3. Motor bearings are loud

4. Air filters rattle

5. Impeller fan is loose, unbalanced or

damaged

6. Motor base is loose in the cabinet

1. Inspect all hardware and retighten or replace

2. Check position of fan and cover

Adjust or replace loose/damaged part

3. Rotate motor shaft to isolate the issue

Replace worn bearings

4. Inspect and reposition filters

5. Turn machine off and unplug from power.

-Inspect impeller for bent or damaged areas.

-Secure impeller on motor shaft and replace if

any damage is found

6. Tighten any loose fasteners

Poor air flow

and dust

collection

1. Filters are dirty

2. Poor system location in shop

1. Clean or replace both air filters frequently. See

page 12

2. Reposition system in the shop for best air

circulation. Refer page 9 for proper air

filtration system placement

TO PREVENT INJURY TO YOURSELF

or damage to the Air Filtration System, turn the switch to the

machine “OFF” and unplug the power cord from the electrical receptacle before making any adjustments.

Содержание 62-450





















Результаты поиска

Содержание 62-450

Отзывы:

Похожие инструкции для 62-450

Бренды по названию

Популярные бренды

Rikon Power Tools 62-450, Руководство оператора

Результаты поиска

Содержание 62-450

Отзывы:

Похожие инструкции для 62-450

Бренды по названию

Популярные бренды