Rikon Power Tools 10-3061 Скачать руководство пользователя страница 21

Страница: 21 / 32

TROUBLESHOOTING

PROBLEM

DIAGNOSIS

REMEDY

The machine does not work when

switched on.

1. No power supply.

2. Defective switch.

3 Defective motor.

1. Check the cable for breakage.

2. Replace the lock switch.

3. Defective motor.

The saw blade does not move with the

motor running.

1. The blade tension knob has not been

tightened.

2. The blade has come off one of the

wheels.

3. The saw blade has broken.

4. The drive belt has snapped.

1. Switch off the motor, tighten the blade

tension knob.

2. Open the doors and check.

3. Replace the blade.

4. Replace the belt.

The saw blade does not cut in a straight

line.

1. Rip fence for cutting not used.

2. Feed rate too fast.

3. The blade teeth are dull or damaged.

4. Blade guides not suitably adjusted.

1. Use a rip fence.

2. Put light pressure on the workpiece.

Make sure the saw blade does not bend.

3. Try a new saw blade.

4. Adjust the blade guides (see ADJUST-

MENT instructions).

The saw blade does not cut, or cuts very

slowly.

1. The teeth are dull, caused by cutting

hard material or long use.

2. The saw blade was fitted the wrong

way on the bandsaw.

1. Replace the saw blade, use a 6 T.P.I.

saw blade for wood and soft material.

Use a 14 T.P.I. saw blade for harder

materials. A 14 T.P.I. saw blade always

cuts slower due to the finer teeth and the

slower cutting performance.

2. Fit the saw blade correctly.

Sawdust builds up inside the machine.

This is normal

Clean the machine regularly. Open the

doors and remove the sawdust with a

vacuum cleaner.

Sawdust inside the motor housing.

This is normal

Clean the ventilating slots of the motor

with a vacuum cleaner. From time to time

remove the sawdust to prevent it from

being drawn into the housing.

The machine does not cut at

45 or 90

degrees.

1. The table is not at right angles to the

blade.

2. The saw blade is dull or too much pres-

sure was put on the workpiece.

1. Adjust the table.

2. Replace the saw blade or put less

pressure on the workpiece.

Green

White

Black

SWITCH

Green

Black
White

Red

White

Blue

MOTOR

115V 60Hz

This machine must be grounded. To avoid electrocution or fire, any repairs to electrical system should

be done only by a qualified electrician, using genuine replacement parts. See page 5 for additional electrical information.

ELECTRICAL

10-3061 Bandsaw - 1/2HP, 110V, 5.5A, 60Hz, 1Ph Motor

Содержание 10-3061

































Результаты поиска

Содержание 10-3061

Отзывы:

Похожие инструкции для 10-3061

Бренды по названию

Популярные бренды

Rikon Power Tools 10-3061, Руководство оператора

Результаты поиска

Содержание 10-3061

Отзывы:

Похожие инструкции для 10-3061

Бренды по названию

Популярные бренды