background image

1 Outline of the Product

 

1-1. Preface 

 

 

- 2 - 

 

 
 
 
 
 

Outline of the Product 

 
 
 
 

1-1. Preface 

 
Thank you for choosing our smart transmitter/gas detector head SD-1D(TYPE GP MED EX). Please check 
that the model number of the product you purchased is included in the specifications on this manual. 
 
This manual explains how to use the detector and its specifications. It contains information required for 
using the detector properly. Not only the first-time users but also the users who have already used the 
product must read and understand the operating manual to enhance the knowledge and experience before 
using the detector. 
 
 

1-2. Purpose of use 

 

  The detector is a fixed type gas detector head that detects leak of combustible gases and that performs the 

alarm activation when the gas concentration is over the setting value. 
This detector is a safety unit, not an analyzer or densitometer which performs quantitative/qualitative 
analysis/measurement for gases. Please fully understand the features of the detector before using it, so 
that it can be used properly. 

  The detector detects abnormalities in the air caused by presence of gases or other reasons (leak) with the 

built-in gas sensor. The concentrations of detected gases are displayed on the seven-segment LED. 

  An external pump etc. outside the detector introduces gas to perform gas detection. 

  The detector has a built-in alarm contact and can be used either as a gas alarm, fault alarm, or common 

(gas, fault) alarm. 

  The detector outputs gas concentration in 4 – 20 mA. 

 
 

1-3. Definition of DANGER, WARNING, CAUTION, and 

NOTE 

 

 DANGER 

This message indicates that improper handling may cause serious 
damage on life, health or assets. 

 WARNING 

This message indicates that improper handling may cause serious 
damage on health or assets. 

 CAUTION 

This message indicates that improper handling may cause minor 
damage on health or assets. 

NOTE 

This message indicates advice on handling. 

 

 

Содержание GP MED EX


























































Отзывы: