Rigol RP5600A Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 22

Rigol RP5600A Скачать руководство пользователя страница 17

RIGOL

User’s Guide for RP5600A

11

Compensation Adjustments

You are suggested to compensate the probe to match with the
oscilloscope. The probes can be adjusted for both low-frequency
compensation and high-frequency compensation. You should make
low-frequency compensation of the probe when it is connected to
the oscilloscope for the first time (or adjust it at any time), while
high-frequency compensation can be made regularly.

Low-frequency compensation

Follow the steps below to make low-frequency compensation:
1

．

Connect the probe to a channel BNC connector and the probe
compensation signal output terminal at the front-panel of the
oscilloscope. Connect the ground alligator lead of the probe to
the “Ground Terminal” under the probe compensation signal
output terminal.

2

．

Press Auto at the front panel of the oscilloscope.

3

．

Set the low-frequency compensation adjustment on the probe
using screwdriver provided via the low-frequency compensation
adjustment hole on the probe to get the flattest pulse possible
(as shown in figures on the next page).

«
...
15
16
17
18
19
...
»

Содержание RP5600A























Отзывы:

Нет отзывов