Rigol PVA7000 Series Скачать руководство пользователя страница 3

Страница: 3 / 26

RIGOL

User Guide for PVA7000 Series Active Probe

Safety Notices and Symbols

Safety Notices in this Manual:

WARNING

Indicates a potentially hazardous situation or practice which, if not
avoided, will result in serious injury or death.

CAUTION

Indicates a potentially hazardous situation or practice which, if not
avoided, could result in damage to the product or loss of important
data.

Safety Terms on the Product:

DANGER

It calls attention to an operation, if not correctly performed,
could result in injury or hazard immediately.

WARNING

It calls attention to an operation, if not correctly performed,
could result in potential injury or hazard.

CAUTION

It calls attention to an operation, if not correctly performed,
could result in damage to the product or other devices
connected to the product.

Safety Symbols on the Product:

Hazardous

Voltage

Safety

Warning

Protective

Earth

Terminal

Chassis
Ground

Test Ground

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Содержание PVA7000 Series



























Результаты поиска

Содержание PVA7000 Series

Отзывы:

Бренды по названию

Популярные бренды

Rigol PVA7000 Series, Руководство пользователя

Результаты поиска

Содержание PVA7000 Series

Отзывы:

Бренды по названию

Популярные бренды