Rigol PVA7000 Series Скачать руководство пользователя страница 2

Страница: 2 / 26

RIGOL

User Guide for PVA7000 Series Active Probe

Guaranty and Declaration

Copyright

2020

RIGOL

Trademark Information

RIGOL

is the trademark of

RIGOL

Publication Number

UGE31101-1110

Notices

⚫

RIGOL

products are covered by P.R.C. and foreign patents, issued and

pending.

⚫

RIGOL

reserves the right to modify or change parts of or all the

specifications and pricing policies at the compan

y’s sole decision.

⚫

Information in this publication replaces all previously released materials.

⚫

Information in this publication is subject to change without notice.

⚫

RIGOL

shall not be liable for either incidental or consequential losses in

connection with the furnishing, use, or performance of this manual, as well
as any information contained.

⚫

Any part of this document is forbidden to be copied, photocopied, or

rearranged without prior written approval of

RIGOL

Product Certification

RIGOL

guarantees that this product conforms to the national and industrial

standards in China as well as the ISO9001:2015 standard and the
ISO14001:2015 standard. Other international standard conformance

certifications are in progress.

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Содержание PVA7000 Series



























Результаты поиска

Содержание PVA7000 Series

Отзывы:

Бренды по названию

Популярные бренды

Rigol PVA7000 Series, Руководство пользователя

Результаты поиска

Содержание PVA7000 Series

Отзывы:

Бренды по названию

Популярные бренды