Manuale ACT 0518
and spreading rate. The
nozzle diameter must always be adjusted for an optimal result (see the indicative table point …). Further
feature of spray guns: they blow air only if the lever is operated (air retaining system).
5. TECHNICAL FEATURES .
The
ACT
spray guns that can be combined with the TMR turbines enable the operator to apply different types of coverage on
different media (metal, wood, masonry ...). The complete system provides for a smooth and uniform surface. The covering product
quantity supplied can be regulated according to its density/viscosity by means of the adjusting screw and
– for the
ACT-S
version
– even by means of the cock on the cover.
Turn the cap to obtain different types of spray with a very limited mist effect (figure .
B
.).
6. WORKABLE COVERAGE MATERIALS (Indicative table) .
ACT, ACT XXL
and
ACT-AS
model: SUITABLE FOR LIGHT AND NOT VERY VISCOSE MATERIALS (PAINTS)
VERNICE A BASE ACQUA O SOLVENTE
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
Nozzle diameter
0,5
0,7
1
1,3
1,7
2,1
2,5
3
3,5
WATER OR SOLVENT VARNISH
Rust preventers
Stains/Primers
Flatting
Micaceous (metallised enamel)
Enamels
Polyurethane enamels
ACT, ACT XXL
and
ACT-S
model: SUITABLE FOR HEAVY AND THICK MATERIALS (PAINTS).
Nozzle diameter
0,5
0,7
1
1,3
1,7
2,1
2,5
3
3,5
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
WALL PAINTS
Water pai nts
Mul ti col ours
Fi ne quartz pai nts
Temperas/Di stempers
ACT
and
ACT XXL
model: SUITABLE FOR ALL TYPES OF MATERIAL, EVEN PLASTIC ONES
Nozzle diameter
0,5
0,7
1
1,3
1,7
2,1
2,5
3
3,5
✔
✔
✔
✔
PLASTIC COVERINGS
Materials with granulometry max 3 mm
Bituminous coating/Tar
To obtain results with good features of mechanical resistance and against atmospheric agents, observe the rules supplied by
the producer of covering products.
7. IMPROPER AND DANGEROUS USES .
If the equipment is used for work cycles other than those specified by the manufacturer, this may damage the equipment and
represent a danger for the operator.
The equipment is not conceived for using dangerous, explosive and/or toxic materials,
herbicides and pesticides.
Our company is not liable for accidents and damage that may occur when the equipment is used by personnel NOT
AUTHORISED and not qualified or for purposes other than those mentioned above.
8. SAFETY RULES .
Attention! Observe the following safety rules:
Consider the environment for use:
- The spray gun is used with paints or solvents; keep in mind that these are highly inflammable;
- Provide for good lighting;
Consider chemical products!
- NEVER USE with foodstuffs or drugs;
- Never point the spray gun against the human body or animals.
Keep tools in a safe place:
- The tools not in use shall be placed in dry and sheltered place;
- Keep unauthorised people away, in particular never leave the tool in a place that can be reached by children;
- Keep the tools clean and always efficient in compliance with operation and maintenance instructions ;
- It is not allowed to use the spray gun in a place subject to explosion-proof rules;
- No source of ignition, such as free flames, lighted cigarettes or cigars, sparks, cables or white-hot objects, overheated surfaces, etc.,
shall be present in the environment where the equipment is used;
- Make sure that the environment is adequately ventilated during use and in the open pay attention to the direction of the wind;
- The operators shall never forget to wear the proper protections while spraying (masks, gloves, protection clothes, etc.);
- Use original spare parts only;
Our company disclaims all responsibility if the a.m. safety rules are not observed. It is not responsible for any kind of
negligence at the time of using the equipment or tampering with it.
