background image

EIGHT HEAD BEAM BAR

16

 

D.  This is not a service contract, and this warranty does not include maintenance, 
cleaning or periodic check-up. During the period specified above, we will replace 
defective parts at its expense, and will absorb all expenses for warranty service 
and repair labor by reason of defects in material or workmanship.  The sole 
responsibility of us under this warranty shall be limited to the repair of the product, 
or replacement thereof, including parts, at the sole discretion of us. 

 

E.  Our company reserves the right to make changes in design and/or 
improvements upon its products without any obligation to include these changes in 
any products theretofore manufactured.  

 

F.  No warranty, whether expressed or implied, is given or made with respect 
to any accessory supplied with products described above. Except to the extent 
prohibited by applicable law, all implied warranties made by us in connection 
with this product, including warranties of merchantability or fitness, are limited 
in duration to the warranty period set forth above. And no warranties, whether 
expressed or implied, including warranties of merchantability or fitness, shall apply 
to this product after said period has expired. The consumer’s and or Dealer’s 
sole remedy shall be such repair or replacement as is expressly provided above; 
and under no circumstances shall we be liable for any loss or damage, direct or 
consequential, arising out of the use of, or inability to use, this product.  

 

G.  This warranty is the only written warranty applicable to our products and 
supersedes all prior warranties and written descriptions of warranty terms and 
conditions heretofore published.  

13. Disclaimer

 

The contents of this manual are subject to change without notice, if in doubt, 
consult your local hotline.

 

Copyright: The data at RIGE Technology Co., Ltd., Guangzhou GeLiang Lighting 
Technology Co.,Ltd common to all, to prohibit any unauthorized copying, printing 
and dissemination.

Содержание RG-ML80B-KEE8H36A



















Отзывы: