Rev. 7 of 11.02.2020
v11/v11R/v11.1R
9 Binding with the Control Panel
The Binding procedure is intended for logging of the Detector in
the control panel (hereinafter, the CP) and transmission of service
information to it.
Prepare the CP for the Detector logging in accordance to the CP
manual.
9.1 Open the case cover by releasing the latch with a screwdriver
(figure 3).
Figure 3
9.2 Install the battery type CR123A (or remove the insulator if the
battery is already installed).
9.3 LED indicator blinking green displays the Detector readiness for
the binding procedure. In case the LED indicator does not blink, close
the «Reset» contacts for a short period.
9.4 After successful binding with the CP, the LED indicator lights
red for 2 sec.
9.5 The «Binding» procedure is limited to 70 sec. After it expires,
the Detector switches to the sleep mode. To resume the «Binding»
mode, «Reset» contacts should be temporary closed.
9.6 Set the detector sensitivity in accordance with the relevant
application conditions (Table 4).
Table 4
Parameter
Pet Immunity
Maximum Range
0
disabled
12 m
1
10 kg
10 m
2
20 kg
10 m
3
40 kg
8 m
10 Choosing Place of Installation
The Detector must be located in the radio-coverage zone of it’s
CP. Therefore, it is advisable to appraise quality of communication
beforehand. The procedure of communication quality appraising is
described in the chapter №11
«Communication Quality Appraising».
When choosing the Detector installation place, it is advisable
to take note of the fact that the detection zone may be limited by
non-transparent objects (curtains, houseplants, cabinets, bookcases,
etc.), as well as glass and mesh partitions. There must be no windows,
air conditioners, space heaters or heating radiators in the Detector
visibility zone. The presence of furniture items on which an animal may
climb in the detection zone may cause a false alarm.
Recommended installation height
—
2.3 m from the floor.
The Detector should be installed at a distance not less than 0.5 m
from electric cables.
11 Communication Quality Appraising
Before installing the Detector to it’s place of operation, it is advisable
to appraise the CP communication quality as follows:
11.1 Prepare the Detector for operation and put it on it’s location
place with a closed cover;
11.2 Open the Detector case, whereupon the Detector will indicate
the quality of CP communication.
Table 5
LED Indication
Communication Quality
Appraisal
Recommendations
LED indicator blinks green
three times
Excellent
Install the Detector at
this place
LED indicator blinks green
two times
Good
LED indicator blinks green
one time
Communication
established
Use repeaters of the
Ladoga RK system
LED indicator blinks red four
times
No communication
12 Installing the Detector
Before installing the detector, it is necessary to remove the cover
with the PCB. For this purpose:
- remove the cover of the Detector;
- drill the holes (Figure 2 b) in the base of the Detector case. They
will be used for fastening the Detector;
- choose the installation place, mark out and drill the installation holes
in the wall with regard to the position of the holes on the Detector base;
- fasten the Detector base in the chosen place;
- put on the cover.
Note
—
To exclude false alarms in pet immunity mode, the Detector
should be installed vertically.
13 Functional Testing
Start movement across the detection zone. After 3 – 4 steps inside
the detection zone, the Detector should indicate intrusion by shot-term
LED lighting red. Wait for 10 s and after it continue movement across
the detection zone. Under movement absence inside the protected
area, LED indication should not light.
14 Detector Behavior
14.1 The Detector is powered on and off by installation and removal
of the main power-supply battery.
14.2 After loss of communication with the CP, the Detector will
continue to search for the CP. If the CP is disabled for a long time, it
is recommended to power off the Detector (see Cl. 14.1).
14.3. It must be taken into account that in case of the Detector
operation 5 °C to minus 20 °C temperature range, the battery
life may be less than 5 years.
ATTENTION!
The Detector must be checked at least annually in
order to test it’s performance.
15 Storage and Transportation
15.1 The Detectors in their original packaging are resistant to:
- transport jolting with the acceleration up to 30 m/sec
2
at impact
frequency range
from 10 to 120 per minute or 15 000 strikes;
- ambient temperature range minus 50 ... +50 °С;
- relative air humidity (95 ± 3) % at a tempe35 °С.
15.2 The Detectors in original package may be transported by
any means of transportation in closed vehicles over any distances in
compliance with the existing shipping rules concerning the respective
means of transportation.
15.3 After transportation under the conditions different to
exploitation conditions the Detectors shall be ready to operate after
a maximum of six hours.
15.4 During storage period lithium batteries should be removed from
the holders or isolators should be installed between a battery “+” and
a holder.
The storage premises should not contain any current-conducting
dust, acid and alkali fumes, or corrosive or destroying insulation gases.
16 Manufacturer’s Guarantees
16.1 The Manufacturer guarantees conformity of the Detector to
it’s Technical Specifications if conditions of transportation, storage,
assembling and operation are observed. The guaranteed storage
period is 63 months since the date of manufacturing the Detector.
16.2 The guaranteed period of operation is 60 months since the date
of commissioning within the storage period guaranteed.
16.3 The Detectors that are found to non-conforming to their
Technical Requirements shall be repaired by the Manufacturer,
provided that the installation and operation rules have been complied
with.
Note
—
Warranty obligations are not applied to the power-supply
batteries.
17 Packing Certificate
Wireless passive infrared detector «Pyrone-4RK» manufactured in
accordance with current technical documentation is classified as fit
for operation and is packed by «RIELTA» JSC.
Packing date _______________________________
month, year
«RIELTA» JSC, www.rielta.com
Chapaeva Str. 17, Saint Petersburg, Russia, 197046, [email protected]
Tel./fax: +7 (812) 233-03-02, +7 (812) 703-13-60
Technical support, tel.: +7 (812) 233-29-53, +7 (812) 703-13-57, [email protected]
Made in Russia
