manualshive.com logo in svg

Riello RS 280, Инструкции по установке, использованию и обслуживанию

Поделиться
Скачать
Riello RS 280 Скачать руководство пользователя страница 32

20122392

30 

GB

Start-up, calibration and operation of the burner

5.5

Burner start-up

Feed electricity to the burner via the disconnecting switch on the
boiler panel.

Close the thermostats/pressure switches, set the parameters on
the RWF55 regulator. 

Please refer to the specific manual for this operation. 

Turn the switch of Fig. 29 to position 

“ON”

 and turn the switch of

Fig. 29 to position 

“LOCAL”

.

5.6

Adjusting gas/air delivery

Move slowly towards the maximum output (butterfly gas valve
completely open);

adjust the required maximum output with the gas pressure sta-
bilizer;

adjust the combustion parameters with the air servomotor and
store the maximum combustion point;

complete the procedure slowly, synchronizing the combustion
with the two servomotors and storing the different setting
points.

DANGER

Make sure that the lamps or testers connected to
the solenoids, or indicator lights on the solenoids
themselves, show that no voltage is present. If volt-
age is present, stop the burner 

immediately 

and

check the electrical wiring.

WARNING

For the start-up procedure and the parameters
calibration, refer to the specific instruction man-
ual of the LMV37... electronic cam supplied with
the burner.

ON

OFF

REMOTE

LOCAL

Fig. 29

20124957

WARNING

For the start-up procedure and the parame-
ters calibration, refer to the specific instruc-
tion manual of the LMV37... electronic cam
supplied with the burner.

Содержание RS 280













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды