manualshive.com logo in svg

Riello RL 28/1, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Riello RL 28/1 Скачать руководство пользователя страница 9

8

ELECTRICAL SYSTEM

ELECTRICAL SYSTEM 

as set up by the manu-

facturer

LAYOUT (A)
Burner RL 28/1 (single-phase)

Key to layout (A)

C

- Capacitor

RMO88.53A2 - Control box
F

- Photocell

MV

- Fan motor

TA

- Ignition transformer

TB

- Burner ground

VA

- 1st nozzle solenoid valve

VF

- 2nd nozzle solenoid valve

XP1

- Connector for STATUS

XP7

- 7 pole socket

NOTE

For remote-reset, connect a push-button switch
(NO) between terminal 3 and neutral of the con-
trol box (terminals 15, 16, 17 and 18).

ELECTRICAL CONNECTIONS (B)

set by installer

All the wires to connect to the burner plugs 3)(B)
must be routed through the fairleads, supplied by
the manufacturer for insertion into the holes in
the plate, preferably those on the left side, after
having removed the thin diaphragm effectively
closing the aperture, as already explained
above. 

1 - Pg 11 Single-phase power supply
2 - Pg 9

Control deviceTL

LAYOUT (C)
RL 28/1 burner electrical connection

Cable section not indicated: 1,5 mm

2

Key to layout (C)

h1 - Hourcounter
IN - Manual burner stop switch
S

- Remote lock-out signal

TL - Limit control device system: this shuts

down the burner when the boiler tempera-
ture or pressure exceeds the setpoint
value.

TS - Safety control device system: this oper-

ates when TL is faulty.

X7 - 7 pole plug

NOTE

The RL 28/1 burner has been type-approved for
intermittent operation. This means it should
compulsorily be stopped at least once every 24
hours to enable the control box to check its own
efficiency at start-up. Burner halts are normally
provided for automatically by the boiler load
control system.
If this is not the case, a time switch should be fit-
ted in series to IN to provide for burner shut-
down at least once every 24 hours.

WARNING
Do not invert the neutral with the phase
wire in the electricity supply line.

ELECTRICAL EQUIPMENT FACTORY-SET

(A)

(B)

(C)

ELECTRICAL CONNECTION

ELECTRICAL CONNECTION

D3225

D3282

D3266

Bl

ack

Whi

te

Bl

ue

Содержание RL 28/1

















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды