background image

5

3  PRODUCT RECEIPT

On receipt of your boiler it is suggested that you visually check 

for external damage to the shipping package. 
If the package is damaged, make a note to that effect on the 

Bill of Lading when signing for the shipment. 

 

− Remove the boiler from the shipping packaging. 

 

− Report any damage to the carrier immediately. 

 

− On occasion, items are shipped loose. 

 

− Be sure that you receive the correct number of packages as 

indicated on the Bill of Lading. 

 

− Claims for shortages and damages must be filed with the 

carrier by consignee.

 

− Permission  to  return  goods  must  be  received  from

 the 

manufacturer or your local 

R

 distributor prior to shipping. 

Goods returned to the factory without an authorized Returned 

Goods Receipt number will not be accepted. 

All returned goods 

are subject to a restocking charge. Written permission must 

be  obtained  through  a  local  Riello  distributor  and  must 

be  obtained  by  your  qualified  service  technician.  Contact 

your installing/service contractor to initiate a claim. Do not 

contact Riello S.p.A. or Evergreen Products International Inc. 

as they cannot provide technical assistance unless you are a 

qualified service technician. 

 

− When ordering parts, you must specify the model and serial 

number of the boiler. Parts can only be purchased through 

an authorized Riello distributor by your installation/service 

technician.

 

When ordering under warranty conditions, your installation/

service technician must also specify the date of installation. 

 

− Purchased parts are subject to replacement only under the 

manufacturer’s warranty. Debits for defective replacement 

parts will not be accepted and will be replaced in kind only 

per 

R

 standard warrant.

4  INTRODUCTION

The 

Residence PRO

 boilers have a new ACC (Active Combustion 

Control) system.

This new control system ensures functionality, efficiency and low 

emissions under any conditions. 

The  ACC  system  uses  an  ionization  sensor  (flame  sensor)

immersed in the burner flame, whose information allows the 

control board to operate the gas valve that regulates the fuel.

This sophisticated control system provides the auto-regulation 

of the combustion, so there is no need for an initial calibration; 

however, it is recommended (required in some jurisdictions) that 

a combustion analysis is performed during initial start-up and 

annual maintenance by a qualified installer or service agency.

The ACC system is able to adapt the boiler to operate with different 

gas compositions, different air inlet and exhaust vent lengths 

and different altitudes (within the specified design limits).

The ACC system can also perform an auto-diagnostic operation 

that locks out the burner before the permitted upper emission 

limit is exceeded.

Residence PRO

  is  a  direct  vent,  Category  IV,  wall  hung  fan 

assisted  room-sealed  condensing  boiler  f

or heating and 

production of domestic hot water

.

This  appliance  is  designed  for  use  with  a  sealed  system  only; 

consequently it is not intended for use on power vented system.

This manual is an integral part of the appliance. It is therefore necessary 

to ensure that the manual is handed to the person responsible for the 

property in which the appliance is located/installed. A replacement 

copy can be obtained from www.egproductsolutions.com

.

IMPORTANT

It is the law that all gas appliances are installed by a competent 

person.

It is in your own interest and that of safety to ensure that the law 

is complied with

.

 

− The  installation  must  conform  to  the  requirements  of  the 

authority  having  jurisdiction  or,  in  the  absence  of  such 

requirements, to the National Fuel Gas Code, ANSI Z223.1/NFPA 

54. Where  required  by  the  authority  having  jurisdiction,  the 

installation  must  conform  to  the  Standard  for  Controls  and 

Safety Devices for Automatically Fired Boilers, ANSI/ASME CSD-1.

 

− The installation should conform with CAN/CSA B149.1 INSTALLATION 

CODE and/or local installation Code, plumbing or waste water 

codes and other codes as applicable

.

 

− Clearances from combustible material must be strictly adhered to.

 

− Manufacturers instructions must NOT be interpreted in anyway 

as overriding local regulations.

Содержание Residence PRO 32 KIS





















Отзывы: