background image

6

 

INSTALLATION

INSTALLATION

UNPACKING THE PRODUCT

R

 

RBS 2S

 solar heaters are supplied in a single package on a 

wooden pallet.

The insulation and the lining components of the models 800 

and 1000 are supplied separately from the structural work and 

are to be assembled upon receiving the product as described 

in the paragraph "Assembly of the insulation and the lining 

(models 800 - 1000)". For these models the magnesium anode 

is supplied in a cardboard box.

The following items are delivered in a plastic bag inside the 

packaging:

 

− Instruction manual

 

− Bar code label

 

− Hydraulic test certificate

 

− Energy label (to be applied to device upon installation)

 

− No. 4 adjustable feet to be mounted during installation 

(for models 800 - 1000 only).

 

9

The instruction manual is an integral part of the solar stor-

age cylinder. Once located, read it thoroughly and keep it 

safe.

 

9

For handling operations, thoroughly follow the instructions 

on device package label.

ASSEMBLY OF THE INSULATION AND THE LINING 
(MODELS 800 - 1000)

The assembly of the insulation and lining components must be 

performed at the site of installation to facilitate passage through 

any doors and/or entries to the room.

4

5

2

1

7

3

3

1

6

1

3

L

3

L

Proceed as follows:

 

− Fit the magnesium anode (6) with its seal in the sleeve 

and fix it in place

 

− Assemble the insulating covers (1) around the body of 

the heater, making sure that the engagement points on 

the edges are positioned correctly. The edges are not re-

quired to be closed completely

 

− Place the front protection plate (3) correctly on the at-

tachments

 

− Place the washers on the attachments and the protec-

tion for the inspection flange (4)

 

− Place the rear protection plate by closing the interlock-

ing flaps (L) without closing completely (leave one tooth 

open)

 

− Apply the upper insulation (2) and the upper cover (5) (in 

order to insert the cover, exert a light and homogeneous 

pressure)

 

− Close  the  interlocking  flaps  (L)  completely,  which  were 

previously left with an open tooth

 

− Fit  the  cover  of  the  inspection  flange  using  the  two 

self-tapping screws (7) provided

 

− Apply the technical data plate and serial number plate.

 

If disassembling is required, proceed in reverse order.

 

9

Wear suitable personal protective equipment and use suit-

able safety devices.

PLACE OF INSTALLATION

R

 

RBS 2S

 solar heaters can be installed in all rooms not re-

quiring a level of electrical protection of the device greater than 

IP X0D.

≥ 0,3 m

≥ 0,3 m

≥ 0,3 m

≥ 0,6 m

≥ 0,7 m

NOTE:

 the above-indicated dimensions are recommended for a 

correct maintenance and access to the device.

9.1 

Installation in older systems and systems 
requiring modernisation

When installing 

R

 

RBS 2S

 storage cylinders in old systems or 

systems requiring modernisation, always perform the following 

checks.

 

− Make sure that the system is fitted with safety and con-

trol devices in accordance with applicable legislation and 

standards

 

− Make sure that the central heating circuit has been 

flushed out to remove all sludge and lime scale, and has 

been vented and seal tested

 

− Make sure that a suitable water treatment system is in-

stalled if the quality of the supply/recirculation water so 

demands (refer to the reference values listed in the table 

alongside).

10 

WATER QUALITY REQUIREMENTS

REFERENCE VALUES

pH

6-8

Electrical conductivity

less than 200 μS/cm (25°C)

Chlorine ions

less than 50 ppm

Sulphuric acid ions

less than 50 ppm

Total iron

less than 0.3 ppm

Alkalinity M

less than 50 ppm

Total hardness

less than 35°F

Sulphur ions

none

Ammonia ions

none

Silicon ions

less than 30 ppm

 

The values above ensure proper operation of the system. Refer 

to the limit values specified in the current standards and regu-

lations on the installation site.

Installation

Содержание RBS 1000 2S













Отзывы: