background image

20170350

32 

GB

Maintenance

Flame presence check 

Check the level of the flame detection signal with the “Check
mode” function from the flame control: LEDs from 2 to 6 indicate
the flame signal level, respectively. "LED indicator and special
function” on page 33
.

Check Mode

With burner flame on:

hold the reset button on the flame control pressed for at
least 3 sec.;

the button colour will change from green to yellow;

each operating status signalling LED will be compared to
20% of the maximum brightness;

press the reset button again (<0.5sec) to reset the standard
operation of the signalling LEDs.

8.2.3

Safety components

The safety components should be replaced at the end of their life
cycle indicated in the following table.
The specified life cycles do not refer to the warranty terms
indicated in the delivery or payment conditions.

Tab. M

8.3

Opening the burner 

To open the burner, proceed as indicated in paragraph "Securing
the burner to the boiler” on page 17.

8.4

Closing the burner 

Refit following the steps described but in reverse order; refit all
burner components as they were originally assembled.

Safety
component

Life cycle

Flame control

10 years or 250.000

operation cycles

Flame sensor

10 years or 250.000

operation cycles

Gas valves (solenoid)

10 years or 250.000

operation cycles

Pressure switches

10 years or 250.000

operation cycles

Pressure adjuster

15 years

Servomotor (electronic cam)

10 years or 250.000

operation cycles

Oil valve (solenoid)

10 years or 250.000

operation cycles

Oil regulator 

10 years or 250.000

operation cycles

Pipes/ oil fittings (metallic)

10 years

Flexible hoses (if present)

5 years or 30.000 pressurised 

cycles

Fan impeller

10 years or 500.000 start-ups

DANGER

Disconnect the electrical supply from the burner
by means of the system main switch.

DANGER

Close the fuel shut-off valve.

Wait for the components in contact with heat
sources to cool down completely.

After carrying out maintenance, cleaning or
checking operations, reassemble the cover and
all the safety and protection devices of the burner.

Содержание P 300 P/G

























































Отзывы: