background image

RIEJU  S.A.    is  grateful  for  the  confidence  you  have  put  in  their  company  and  would  like  to 
congratulate you on your choice of mortorbike.

The  Marathon  125/200  c.c.  are  the  resulted  of  the  long-term  experience  that  RIEJU  has  had  in 
competitions, which has led to the development of a high performance vehicle.

The objective of this owner’s manual is to denote the use and maintenance of your vehicle, we ask 
you to read the instructions and information that follow carefully.

We wish to remind you that the life of the vehicle depends on how it is maintained. Maintaining the 
vehi-cle in perfect working condition reduces the cost of repair.

This manual has to be considered as an integrate component of the mortorbike and must remain part 
of the basic equipment, and handed over in the event of a change of vehicle ownership. 

In the event of any problems, please consult the RIEJU dealer who will assist you.

Please remember that for your mortorbike to perform correctly, you should always 

fit original spare

 

parts. 

1

Manual Usuari Marathon 125, PRO 125 Eng.qxp  23/10/2009  16:44  Página 1

Содержание Enduro


















































Отзывы: