RIEJU Enduro Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 49

background image

ROUTINE TESTING

21

FRONT BRAKE

Pulling in the front brake lever operates the front brake by
pumping brake fluid from the master cylinder to the front
brake calliper. The brake pads are pushed by the calliper
pistons against the front disc. Slowing the bike down.
The braking surface of the disc should be free of oil and
dirt to ensure maximum braking efficiency. If for any rea-
son the master cylinder is empty of brake fluid after chec-
king for pad wear it should be topped up as necessary. If
there is air in the system the brakes will need to be bled.
Loosen the bleed nipple on the front calliper, putting a
petrol tube onto the nipple. This tube should be put in a
recipient so as not to spill brake fluid. Undo the brake nip-
ple on the calliper 1 or 2 turns only and gently operate the
front brake lever so that the brake fluid goes down, until it
comes out through the tube without any air bubbles. At this
point, hold the brake lever in and close the bleed nipple.
Top up the master cylinder reservoir as necessary with DOT
4 brake fluid. Replace the top and check brake efficiency.

Bleed nipple

Manual Usuari Marathon 125, PRO 125 Eng.qxp 23/10/2009 16:44 Página 14

«
...
23
24
25
26
27
...
»

Содержание Enduro


















































Отзывы:

Нет отзывов

Похожие инструкции для Enduro

Бренд: X-lite Страницы: 5

TroyLee Designs

Бренд: A3 HELMET Страницы: 244

Бренд: Honda Страницы: 25

Бренд: Ohlins Страницы: 8

Бренд: KTM Power Parts Страницы: 7

SEMIFAIRING BATWING SML TOURING

Бренд: PUIG Страницы: 3

Бренд: RPS Страницы: 28

Бренд: Suzuki Страницы: 165

Бренд: Kabuto Страницы: 6

Бренд: Sachs Bikes Страницы: 84

80 MasterGuard (L+K)

Бренд: SCHUBERTH Страницы: 44

Бренд: Yamaha Страницы: 108

Бренд: Yamaha Страницы: 114

Бренд: Yamaha Страницы: 168

Бренд: Yamaha Страницы: 497

Бренд: Yamaha Страницы: 704

Бренд: Yamaha Страницы: 84

Бренд: Yamaha Страницы: 390

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды