Riedel BP-2002 Скачать руководство пользователя страница 9

Страница: 9 / 11

5 Connecting Options

5.1 Headset:

4-pin XLR-male for headset with dynamic or electret microphone

Pin Definition

GND

Microphone high

3 Loudspeaker low

4 Loudspeaker high

5.2 Intercom Line Connector

At this point, it is important to observe the different modes for RPL and Clear-Com



. In RPL mode, two channels are

available on a 3-pin XLR connector. In CC mode, by contrast, pin 2 is used only for the supply voltage of 30 VDC+. No
audio is provided on pin 2. The intercom connectors are looped through. Accordingly, pin 1 (female) is connected to

pin 1 (male), and so on.

5.2.1 Intercom line connector in RPL Mode

3-pin XLR male and XLR female

Pin Definition

Ground

Audio channel B and +30 VDC

Audio channel A

5.2.2 Intercom line connectors in Clear-Com



-Mode

3-pin XLR male and XLR female

Pin Definition

Ground

+30 VDC

Audio

RIEDEL RPL_EN_BP-2002e-Rev2.1.doc: 2 12.12.2002 11:29

Page 9 of 11

Röttgen 8, D-42109 Wuppertal,

Alterations reserved

Tel. +49 (0) 202 / 270 370

Содержание BP-2002












Результаты поиска

Содержание BP-2002

Отзывы:

Похожие инструкции для BP-2002

Бренды по названию

Популярные бренды

Riedel BP-2002, Руководство по эксплуатации

Результаты поиска

Содержание BP-2002

Отзывы:

Похожие инструкции для BP-2002

Бренды по названию

Популярные бренды