background image

6

ASSEMBLY

NOTE:  Remove Powerhead Assembly 
from Dust Drum prior to assembly of 
Casters and Caster Feet.

1. Turn Dust Drum upside down on floor.

2. Place Caster Foot on floor. Insert the

stem of a Caster into socket of Caster
Foot.

3. Push on the Caster until the Caster ball

end snaps fully into the Socket and the
Caster swivel freely. Repeat for other
three Casters and Caster Feet.

4. Place Caster Foot with Caster over

post on bottom of Dust Drum and press
firmly in place, as shown.

5. Repeat for the other three Caster/

Caster Foot assemblies.

6. Turn the Dust Drum upright.

Caster/Caster Foot Assembly

Wet/Dry Vac Assembly

Caster 

Foot

Caster

Caster Ball

Caster Stem

Caster Foot 

Post Hole

Caster Foot

Post

Dust

Drum

2. Press in on the two Latches located

on either side of the Dust Drum until
they snap into place, securing the
Powerhead Assembly to the Dust Drum.

3. To remove the Powerhead Assembly,

pull out on the two Latches and lift
Powerhead Assembly from the Dust
Drum. Do not force the Latches to
rotate more than slightly outside Drum
Flange.

Drum 

Latches

(1 on each 

side)

Dust Drum

Powerhead 

Assembly

Attaching Powerhead Assembly 
to Dust Drum

1. Place Powerhead Assembly on top of

Dust Drum with the Extended Lip of the
Lid aligned with the Vac Inlet. Be sure
Powerhead Assembly is fully seated on
the Dust Drum.

Extended 

Lip

Vac 

Inlet

Dust 

Drum

Powerhead 

Assembly

SP7054 RT12000.indb   6

9/5/18   12:04 PM

Содержание RT12000

















Отзывы: