background image

11

OPERATION

TO CHARGE 

A fully discharged battery pack with a temperature between 
32°F (0°C) and 150°F (65°C) will charge in about an hour.

 

Charge the 24 Volt lithium-ion battery pack only with the 
charger provided.

  Connect the charger to a power supply.

  NOTE:

 

If  needed

,

 

the  charger  can  operate  with  most 

generators and inverters rated at 300 Watts or higher.

  Attach the battery pack to the charger by aligning the 

raised ribs on the battery pack with the grooves in the 
charger,  then  slide  the  battery  pack  onto  the  charger. 

See Figure 2.

  Do not place the charger in an area of extreme heat or 

cold. It will work best at normal room temperature.

  After  charging  is  complete,  the  continuous  green  light 

will come on and the charge level indicator lights on the 
battery will go off.

  The charger will keep the battery pack fully charged if left 

on the charger.

CHARGE LEVEL INDICATOR

See Figure 3.

The charge level indicator shows that the battery is charged 
at 1/4, 1/2, 3/4, or full capacity. To display the amount of 
charge left in the battery, press and hold the charge level 
indicator button. 
NOTE:  When  the  battery  pack  contains  less  than  10% 
charge, the 1/4 charge level indicator will flash.

CHARGING A HOT BATTERY PACK

If the battery pack is above normal temperature range, the 
red LED will begin flashing and the green LED will be off. 
When the battery pack cools down to approximately 150°F 
(65°C), the charger will automatically begin fast charge mode.
NOTE:  Refer  to  CHARGING  THE  BATTERY  PACK  for 
normal recharging of batteries. If the charger does not charge 
the battery pack under normal circumstances, return both 
the battery pack and charger to your nearest repair center 
for electrical check. For the location of your nearest repair 
center, please call 1-866-539-1710.

CHARGING A COOL BATTERY PACK

If the battery pack is below normal temperature range, the 
red LED will begin flashing and the green LED will be off. 
When the battery warms to a temperature of more than 14°F  
(-10°C), the charger will automatically begin charge mode.

COLD WEATHER OPERATION

The lithium-ion battery pack can be used in temperatures 
down to -4°F. When the battery pack is very cold, it may 
“buzz”  for  the  first  minute  of  use  to  warm  itself  up.  Put 
the battery pack on a tool and use the tool in a light duty 
application. After about a minute, the pack will have warmed 
itself up and begin operating normally.

24v

XLi

?

Fig. 3

1/4 

CAPACITY

FULL

CAPACITY

CHARGE 

LEVEL  

INDICATOR 

BUTTON

CHARGE 

LEVEL INDICATOR

1/2 

CAPACITY

3/4 

CAPACITY

Fig. 4

EVALUATE

INDICATOR

CHARGING

INDICATOR

FULL

INDICATOR

DEFECTIVE 

INDICATOR

GREEN LED

RED LED

Содержание R8804





















Отзывы:

Похожие инструкции для R8804