9 - English
workpiece. More blade depth will increase the chance of
kickback and cause the cut to be rough.
Remove the battery pack from saw.
Rotate depth lock lever away from the base.
Determine the desired depth of cut.
Hold base flat against the workpiece and raise or lower
saw until the index point or mark on the saw aligns with
the desired depth on the scale.
Rotate depth lock lever toward the base to lock into
position.
OPERATING THE SAW
See Figures 12 - 13, page 14.
It is important to understand the correct method for operating
the saw. Refer to the figures in this section to learn the correct
and incorrect ways for handling the saw.
WARNING:
To make sawing easier and safer, always maintain
proper control of the saw by holding the saw
with two hands. Loss of control could cause an
accident resulting in possible serious injury.
DANGER:
When lifting the saw from the workpiece, the blade
is exposed on the underside of the saw until the
lower blade guard closes. Make sure the lower
blade guard is closed before setting the saw down.
WARNING:
Use clamps or other practical ways to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body
is unstable and may lead to loss of control which
could cause possible serious injury.
To make the best possible cut:
Hold the saw firmly with both hands.
Avoid placing your hand on the workpiece while making
a cut.
Support the workpiece so that the cut (kerf) is always to
your side.
Support the workpiece near the cut.
Clamp the workpiece securely so that the workpiece will
not move during the cut.
Always place the saw on the workpiece that is supported,
not the “cut off” piece.
Place the workpiece with the “good” side down.
Draw a guideline along the desired line of cut before
beginning your cut.
OPERATION
CROSS CUTTING/RIP CUTTING
See Figures 14 - 15, page 14.
When making a cross cut or rip cut, align your line of cut
with the outer blade guide notch on the saw base.
Since blade thicknesses vary, always make a trial cut in
scrap material along a guideline to determine how much, if
any, the guideline must be offset to produce an accurate cut.
NOTE:
The distance from the line of cut to the guideline is
the amount you should offset the guide.
Secure the workpiece.
Clamp a straight edge to the workpiece using C-clamps.
Saw along the straight edge to achieve a straight rip cut.
NOTE:
Do not bind the blade in the cut.
USING OPTIONAL EDGE GUIDE
See Figure 16, page 14.
Use an edge guide, part no. 202050004, when making long
or wide rip cuts with the saw.
Remove the battery pack from the saw.
Place the edge guide (not included) through the slots in
the saw base.
Adjust the edge guide to the width needed.
Tighten the wing screw securely.
When using an edge guide, position the face of the edge
guide firmly against the edge of workpiece. This makes for
a true cut without pinching the blade. The guiding edge of
the workpiece must be straight for your cut to be straight.
Use caution to prevent the blade from binding in the cut.
BEVEL CUTTING
See Figures 17 - 19, pages 14 and 15.
The angle of cut of the saw may be adjusted to any desired
setting between zero and 56°.
NOTE:
When making cuts at 56°, the blade should be set
at full depth of cut.
Since blade thicknesses vary and different angles require
different settings, always make a trial cut in scrap material
along a guideline to determine how much you should offset
the guideline on the board to be cut.
When making a bevel cut, hold the saw firmly with both
hands.
Rest the front edge of the base on the workpiece. Depress
the lock-off button and squeeze the switch trigger to start
the saw. Always let the blade reach full speed, then guide
the saw into the workpiece.
WARNING:
The blade coming in contact with the workpiece
before it reaches full speed could cause saw to
“kickback” toward you resulting in serious injury.
